Tyan Computer B2881 manual Features

Page 11

1.3Features

Enclosure

•Industry 19” rack-mountable 1U chassis storage bay

–(4) 3.5” HDD bays

–(1) slim line CD-ROM bay

–(1) slim line FDD bay

•Dimension: D 25.4 x W 17.17 x H 1.71 inch (645x436x43.6mm)

Processors

•Supports one or two AMD Opter- onTM 200 series processors

Chipset

•AMD-8131 Hyper Transport PCI-X tunnel

•AMD-8111 Hyper Transport I/O hub

•Winbond W83627HF super I/O chip

•ADT7463 Hardware Monitor IC

Memory

•Eight 184-pin 2.5-Volt DDR DIMM sockets

•Supports up to 16GB of Registered, ECC DDR400/333 memory

Expansion Slots

•Two 64-bit 133/100MHz (3.3V) PCI- X slots supporting low profile and standard card

Back I/O Ports

•One keyboard & one PS/2 mouse ports

•Two RJ45 10/100/1000 Base-T port with activity LED

•Two USB 2.0 ports

•One 9-pin UART serial port

•One 15-pin VGA port

Front Panel Features

•I/O

–(2) USB 2.0 ports

•LED indicators

–Power LED

–(2) LAN LEDs

–HDD active LED

•Switches

–Power switch

–Reset switch

Networking

•(2) Gigabit Ethernet ports (Broad- com BCM5704 dual port controller) connected to 133MHz PCI-X bus

Video

•ATI RAGE XL PCI graphics control- ler

•8MB Frame Buffer of video memory

Integrated Storage Controller

•Model B2881G24S4H/S4-LC

–Dual channel IDE

–Silicon Image Sil3114 SATA RAID controller, RAID 0,1, and 10 support

•Model B2881G24U4H

–Adaptec AIC-7902N dual-chan- nel U320 SCSI

–SO-DIMM ZCR support

Storage

•SATA version, supports up to 4 internal SATA-1 HDDs

•Optional slim CD-ROM, DVD-ROM and FDD

Motherboard

•Tyan Thunder K8SRE S2881G2NR-

BB

•E-ATX footprint (13” x 12”)

BIOS

•AMI BIOS 8.0 on 4Mbit LPC flash

ROM

•PnP, DMI2.0, WfM2.0 power man- agement

•Power management S1, S4 and S5 support

•ACPI 1.0b & 2.0 support

Server Management

•Automatic fan speed control

•Chassis intrusion alert

•Support Tyan Servr Management (TSM)

•Tyan SMDC* IMPI 1.5 compliant *remote server management kit (option)

Chapter 1: Overview

3

Image 11
Contents Transport GT24 B2881 Service Engineer’s Manual Page Preface Federal Communications Commission FCC Conventions Safety Information Table of Contents Technical Support About the Transport GT24 B2881 OverviewSupport Backplane Product ModelsB2881G24S4H B2881G24U4H B2881G24S4-LC Model HDD Bays Hot-SwapFeatures Regulatory Power SupplyEnvironment Temperature FDD Kit UnpackingRail Kit CD-ROM Accessory Kit for B2881G24S4-LC only B2881G24IU4H/B2881G24S4H About the ProductSystem Front View B2881G24S4-LC LED Definition Front Panel System Rear ViewRear I/O LED FAN1 System Internal View B2881G24S4-LCB2881G24S4H 109B2881G24U4H 109 Motherboard Layout Jumpers & Connectors Function Motherboard Block Diagram Tools Before You BeginWork Area Precautions Rack mounting kit Installing the Server in a RackRack Mounting Installing Outer Rails to the Rack Installing the Inner Rails to ChassisLocate the front and rear brackets Remember to add washer Front Side Rear Side Rackmounting the Server Setting Up Removing the Chassis Cover Installing Motherboard ComponentsInstalling the CPU, Heatsink and Air Duct Setting Up Installing the Memory Installing a PCI-X Card Setting Up Installing the Hard Drive for B2881G24S4-LC Setting Up Installing the Hard Drive for B2881G24S4H/U4H Setting Up Installing the Slim FDD Option Connect the other side to the connector on motherboard Installing the CD-ROM or DVD-ROM for B2881G24S4-LC only Power Cable Data Cable Introduction Replacing Pre-Installed ComponentsPrecautions Following flowchart outlines the disassembly procedure Disassembly FlowchartRemoving the Cover Replacing Motherboard Components Disconnecting All Motherboard CablesMain Power EPS 12V Power Disconnect all fan power cables Removing the Motherboard Replacing the LED Control Board Replacing Pre-Installed Components Replacing the M1012 Adapter Board J3 LAN/ID LED 1 M1012 Adapter Board Features2 M1012 Adapter Board Connector Pin Definition FAN Signal Related Connector Pin Definition GND FAN1TACH FAN2TACH FAN3TACH KEY PIN FAN312VPWM FAN3TACH GND FAN4TACH FAN412VPWM FAN912VPWM FAN9TACH GND FAN10TACH System Fan Layout System Fan Monitoring Signal System Fan Speed Control SignalReplacing the Sata or Scsi Backplane Replacing Pre-Installed Components ATA Backplane M1204 Features Replacing Pre-Installed Components M1204 HDD Access LED Connector Pin Definition Scsi Backplane M1205 Features Replacing Pre-Installed Components Tion M1205 HDD Start-Mode & ID Selection SwitchCase Motor Spin FuncLeft to right in front view ID SequenceReplacing the Power Supply S2881 Advanced/Hardware Health Information B2881 Advanced/Hardware Health InformationTable of Differences S2881 B2881 Appendix II Cable Connection Tables Power Supply Cable FDD Related Cable Option Help Resources Technical SupportReturning Merchandise for Service