Tyan Computer B2881 manual Conventions

Page 5

About this Manual

This manual provides you with instructions on installing your Transport GT24, and consists of the following sections:

Chapter 1: Provides an Introduction to the Transport GT24 B2881 bare-bones, packing list, describes the external components, gives a table of key compo- nents, and provides block diagrams of the system.

Chapter 2: Covers procedures on installing the CPU, mem- ory modules, an optional PCI card, and hard drives.

Chapter 3: Covers removal and replacement procedures for pre-installed components.

Appendix: Describes the differences between mainboard BIOS and system BIOS. The cable connection tables are also provided for reference of system setup.

Conventions

The following conventions are used in the manual:

Note: Calls attention to important information.

Warning: Provides information to prevent harm to user or damage to equipment .

iii

Image 5

Contents Transport GT24 B2881 Service Engineer’s Manual Page Preface Federal Communications Commission FCC Conventions Safety Information Table of Contents Technical Support About the Transport GT24 B2881 OverviewB2881G24S4H B2881G24U4H B2881G24S4-LC Product ModelsModel HDD Bays Hot-Swap Support BackplaneFeatures Regulatory Power SupplyEnvironment Temperature FDD Kit UnpackingRail Kit CD-ROM Accessory Kit for B2881G24S4-LC only B2881G24IU4H/B2881G24S4H About the ProductSystem Front View B2881G24S4-LC LED Definition Front Panel System Rear ViewRear I/O LED FAN1 System Internal View B2881G24S4-LCB2881G24S4H 109B2881G24U4H 109 Motherboard Layout Jumpers & Connectors Function Motherboard Block Diagram Tools Before You BeginWork Area Precautions Rack mounting kit Installing the Server in a RackRack Mounting Installing Outer Rails to the Rack Installing the Inner Rails to ChassisLocate the front and rear brackets Remember to add washer Front Side Rear Side Rackmounting the Server Setting Up Removing the Chassis Cover Installing Motherboard ComponentsInstalling the CPU, Heatsink and Air Duct Setting Up Installing the Memory Installing a PCI-X Card Setting Up Installing the Hard Drive for B2881G24S4-LC Setting Up Installing the Hard Drive for B2881G24S4H/U4H Setting Up Installing the Slim FDD Option Connect the other side to the connector on motherboard Installing the CD-ROM or DVD-ROM for B2881G24S4-LC only Power Cable Data Cable Introduction Replacing Pre-Installed ComponentsPrecautions Following flowchart outlines the disassembly procedure Disassembly FlowchartRemoving the Cover Replacing Motherboard Components Disconnecting All Motherboard CablesMain Power EPS 12V Power Disconnect all fan power cables Removing the Motherboard Replacing the LED Control Board Replacing Pre-Installed Components Replacing the M1012 Adapter Board J3 LAN/ID LED 1 M1012 Adapter Board Features2 M1012 Adapter Board Connector Pin Definition FAN Signal Related Connector Pin Definition GND FAN1TACH FAN2TACH FAN3TACH KEY PIN FAN312VPWM FAN3TACH GND FAN4TACH FAN412VPWM FAN912VPWM FAN9TACH GND FAN10TACH System Fan Layout System Fan Monitoring Signal System Fan Speed Control SignalReplacing the Sata or Scsi Backplane Replacing Pre-Installed Components ATA Backplane M1204 Features Replacing Pre-Installed Components M1204 HDD Access LED Connector Pin Definition Scsi Backplane M1205 Features Replacing Pre-Installed Components Case M1205 HDD Start-Mode & ID Selection SwitchMotor Spin Func TionLeft to right in front view ID SequenceReplacing the Power Supply S2881 Advanced/Hardware Health Information B2881 Advanced/Hardware Health InformationTable of Differences S2881 B2881 Appendix II Cable Connection Tables Power Supply Cable FDD Related Cable Option Help Resources Technical SupportReturning Merchandise for Service