Tyan Computer B2881 manual Federal Communications Commission FCC

Page 4

Federal Communications Commission (FCC)

Notice for the USA Compliance Information State- ment (Declaration of Conformity Procedure) DoC FCC Part 15: This device complies with part 15 of the FCC Rules

Operation is subject to the following conditions:

1)This device may not cause harmful interference, and

2)This device must accept any interference received including inter- ference that may cause undesired operation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and the receiver.

Plug the equipment into an outlet on a circuit different from that of the receiver.

Consult the dealer on an experienced radio/television technician for help.

Notice for Canada

This apparatus complies with the Class B limits for radio interference as specified in the Canadian Department of Communications Radio Interference Regulations. (Cet appareil est conforme aux norms de Classe B d’interference radio tel que specifie par le Ministere Cana- dien des Communications dans les reglements d’ineteference radio.)

Notice for Europe (CE Mark) This product is in conformity with the Council Directive 89/336/EEC, 92/31/EEC (EMC).

CAUTION: Lithium battery included with this board. Do not puncture, mutilate, or dispose of battery in fire. Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by manufacturer. Dispose of used battery according to manufacturer instructions and in accordance with your local regulations.

ii

Image 4
Contents Transport GT24 B2881 Service Engineer’s Manual Page Preface Federal Communications Commission FCC Conventions Safety Information Table of Contents Technical Support Overview About the Transport GT24 B2881Product Models B2881G24S4H B2881G24U4H B2881G24S4-LCModel HDD Bays Hot-Swap Support BackplaneFeatures Environment Temperature Power SupplyRegulatory Unpacking FDD KitRail Kit CD-ROM Accessory Kit for B2881G24S4-LC only System Front View B2881G24S4-LC About the ProductB2881G24IU4H/B2881G24S4H System Rear View LED Definition Front PanelRear I/O LED System Internal View B2881G24S4-LC FAN1109 B2881G24S4HB2881G24U4H 109 Motherboard Layout Jumpers & Connectors Function Motherboard Block Diagram Work Area Before You BeginTools Precautions Rack Mounting Installing the Server in a RackRack mounting kit Installing the Inner Rails to Chassis Installing Outer Rails to the RackLocate the front and rear brackets Remember to add washer Front Side Rear Side Rackmounting the Server Setting Up Installing Motherboard Components Removing the Chassis CoverInstalling the CPU, Heatsink and Air Duct Setting Up Installing the Memory Installing a PCI-X Card Setting Up Installing the Hard Drive for B2881G24S4-LC Setting Up Installing the Hard Drive for B2881G24S4H/U4H Setting Up Installing the Slim FDD Option Connect the other side to the connector on motherboard Installing the CD-ROM or DVD-ROM for B2881G24S4-LC only Power Cable Data Cable Replacing Pre-Installed Components IntroductionPrecautions Disassembly Flowchart Following flowchart outlines the disassembly procedureRemoving the Cover Main Power EPS 12V Power Disconnecting All Motherboard CablesReplacing Motherboard Components Disconnect all fan power cables Removing the Motherboard Replacing the LED Control Board Replacing Pre-Installed Components Replacing the M1012 Adapter Board 1 M1012 Adapter Board Features J3 LAN/ID LED2 M1012 Adapter Board Connector Pin Definition FAN Signal Related Connector Pin Definition GND FAN1TACH FAN2TACH FAN3TACH KEY PIN FAN312VPWM FAN3TACH GND FAN4TACH FAN412VPWM FAN912VPWM FAN9TACH GND FAN10TACH System Fan Layout System Fan Speed Control Signal System Fan Monitoring SignalReplacing the Sata or Scsi Backplane Replacing Pre-Installed Components ATA Backplane M1204 Features Replacing Pre-Installed Components M1204 HDD Access LED Connector Pin Definition Scsi Backplane M1205 Features Replacing Pre-Installed Components M1205 HDD Start-Mode & ID Selection Switch CaseMotor Spin Func TionID Sequence Left to right in front viewReplacing the Power Supply B2881 Advanced/Hardware Health Information S2881 Advanced/Hardware Health InformationTable of Differences S2881 B2881 Appendix II Cable Connection Tables Power Supply Cable FDD Related Cable Option Technical Support Help ResourcesReturning Merchandise for Service