Perle Systems S-110P-SFP, S-110PP-SFP manual PD Power Reset Switch, Loopback Fiber Switch

Page 9

Down

 

detection

 

 

Down

PSE disabled

 

 

These switches must be set in order to enable the power sourcing function and to indicate the type of device detection required. If the device type is unknown, the default should be used as per IEEE802.3af/at standards.

Enabled: When enabled, the media converter will perform Power Sourcing Equipment (PSE) functions as per IEEE802.3af (POE) or 802.3at-2009 (POE+) standards.

Disabled: When disabled the media converter will not perform PSE functions.

PD Power Reset (Switch 6)

Switch Position

Mode

 

 

Up (default)

Disabled

 

 

Down

Enabled

 

 

Disabled: When disabled, the loss of fiber link has no effect on PSE power to the PD device.

Enabled: When enabled, if the media converter detects loss of link on the fiber port it will turn off PSE output power to the PD device connected to the copper port. After 2 seconds, the media converter will restore power to the PD and the power will remain on until the fiber link transitions from a link up to link down state.

Loopback Fiber (Switch 7)

Switch Position

Mode

 

 

Up (default)

Disabled

 

 

Down

Enabled

 

 

Disabled: The loopback feature is disabled. This is default position for normal operation. The switch must be set to this position in order for data to pass through the media converter.

Enabled: This is a test mode. All data received on the receive (RX) fiber connection is looped back to the transmit (TX) fiber connection. The data link will be disabled; however power to the

9

Perle PoE/PoE+ 10/100 Ethernet Media Converter

 

Installation Guide

Page 8 Page 10
Image 9
Page 8 Page 10
Contents 110P 110PP 110P-SFP Installation GuidePOE/POE+ OverviewPower Sourcing Pinouts InstallationPowering Options Jumper Settings UTP copper Power PoEPoE+ Bank DIP SwitchesDIP Switch Settings Bank Auto-negotiation copper SwitchSwitch Position Copper Port Link Pass-Through Mode Switch Switch Position ModeLink Pass-Through Behaviour PSE Enable Copper Switch 4 Far End Fault SwitchSwitch Position Fiber Port Switch Position TypeLoopback Fiber Switch PD Power Reset SwitchSpeed Copper Switch Duplex Copper SwitchDuplex Fiber Switch Installing the SFP Fiber Module Installing the Duplex Fiber CableAuto/MDIX Switch Installing the Simplex Fiber Cable Installing the Copper CableAttaching the Power Cord Strain Relief Clip Powering up the Perle Media Converter Operation Status LEDLED Pattern Error conditions Other Features Auto-MDIXPause Ieee 802.3xy General TroubleshootingNo connectivity MethodNo Power to the PD Fiber Optic Specifications Technical SpecificationsEthernet Copper Cabling Requirements Fiber Cabling RequirementsFCC Compliance InformationContacting Technical Support Warranty / Registration

S-110PP-SFP, S-110P, S-110P-SFP, S-110PP specifications

Perle Systems is renowned for delivering robust networking solutions, particularly its series of media converters and network devices. Among these, the Perle S-110PP, S-110P-SFP, S-110P, and S-110PP-SFP stand out due to their remarkable features and technologies tailored for various networking requirements.

The Perle S-110PP is a PoE (Power over Ethernet) media converter that enables the transmission of both data and power over a single Ethernet cable. This device is particularly beneficial for powering edge devices such as IP cameras, VoIP phones, and wireless access points. It supports standard IEEE 802.3af and 802.3at PoE protocols, ensuring compatibility with a wide range of powered devices. The S-110PP is built to withstand harsh environmental conditions, featuring an industrial-grade design that is tested for reliability and durability.

The S-110P-SFP model introduces flexibility with its SFP (Small Form-factor Pluggable) slot, which allows users to customize their connection types by accommodating different SFP transceivers. This feature enables seamless integration into varying network environments, whether requiring fiber or copper connections. The S-110P-SFP also supports a wide range of data rates, making it suitable for high-speed applications.

On the other hand, the S-110P offers an excellent blend of performance and functionality with its compact design. This model is primarily focused on simple and effective media conversion, ensuring reliable data transmission between different media types, such as twisted pair and fiber optics. The S-110P is ideal for users looking to extend their network over long distances while maintaining high performance.

Lastly, the S-110PP-SFP combines the advantages of the previous models, providing both Power over Ethernet capabilities and the versatility of SFP slots. This hybrid approach not only enhances deployment options but also optimizes the use of existing network infrastructure. The S-110PP-SFP caters to businesses looking to modernize their networks with both power and connectivity solutions in a single, convenient package.

In summary, Perle Systems' S-110 series—comprising S-110PP, S-110P-SFP, S-110P, and S-110PP-SFP—offers a comprehensive suite of features. These devices are built for reliability, flexibility, and exceptional performance, addressing the diverse needs of modern network infrastructures. Whether extending network reach, powering devices, or accommodating varied connection types, the S-110 series is an excellent choice for networking professionals.
Top Page Image Contents