Perle Systems S-110P-SFP, S-110PP manual Troubleshooting, General, No connectivity, Method

Page 17

Troubleshooting

General

∙Ensure power is supplied to the media converter. Only the Perle provided power supply may be used.

∙Ensure the remote device’s fiber connection type is compatible with the media converter. If using a simplex fiber connection, ensure that you have both an Upstream (U) and Downstream (D) media converter.

∙Ensure all cabling is of the correct type and is in good working order.

∙For duplex fiber connections, ensure the RX and TX has been reversed between the two media converters.

No connectivity

If unable to get full connectivity with all DIP switches in the UP position, this procedure is recommended for troubleshooting.

Method 1

1.Set the Link Pass-Through mode to Standard on both media converters. Leave all other switches in the Up position.

2.Connect the copper device to the copper port on the media converter. The LKC LED light indicates good copper connection. If the LKC LED is not lit, then check the copper cable and the attached device.

3.Repeat for the far end media converter.

4.Connect the fiber cable to both media converters. The LKF LED indicates good fiber connection. If no LKF LED then check the fiber cabling. Ensure the transmitter and receiver pairs are crossed.

5.Return units to desired configuration.

Method 2:

The fiber connection can also be verified by configuring the remote media converter for loopback mode. The LKF LEDs on both media converters should be lit. Data should pass through the local converter, over the fiber connection to the remote media converter. At the remote media converter, the data will be looped

17

Perle PoE/PoE+ 10/100 Ethernet Media Converter

 

Installation Guide

Page 16 Page 18
Image 17
Page 16 Page 18
Contents 110P 110PP 110P-SFP Installation GuidePOE/POE+ OverviewPower Sourcing Pinouts InstallationPoE+ Powering Options Jumper SettingsUTP copper Power PoE Bank DIP SwitchesSwitch Position Copper Port DIP Switch Settings BankAuto-negotiation copper Switch Link Pass-Through Behaviour Link Pass-Through Mode SwitchSwitch Position Mode PSE Enable Copper Switch 4 Far End Fault SwitchSwitch Position Fiber Port Switch Position TypeLoopback Fiber Switch PD Power Reset SwitchDuplex Fiber Switch Speed Copper SwitchDuplex Copper Switch Auto/MDIX Switch Installing the SFP Fiber ModuleInstalling the Duplex Fiber Cable Attaching the Power Cord Strain Relief Clip Installing the Simplex Fiber CableInstalling the Copper Cable Powering up the Perle Media Converter LED Pattern OperationStatus LED Error conditions Pause Ieee 802.3xy Other FeaturesAuto-MDIX General TroubleshootingNo connectivity MethodNo Power to the PD Fiber Optic Specifications Technical SpecificationsEthernet Copper Cabling Requirements Fiber Cabling RequirementsFCC Compliance InformationContacting Technical Support Warranty / Registration

S-110PP-SFP, S-110P, S-110P-SFP, S-110PP specifications

Perle Systems is renowned for delivering robust networking solutions, particularly its series of media converters and network devices. Among these, the Perle S-110PP, S-110P-SFP, S-110P, and S-110PP-SFP stand out due to their remarkable features and technologies tailored for various networking requirements.

The Perle S-110PP is a PoE (Power over Ethernet) media converter that enables the transmission of both data and power over a single Ethernet cable. This device is particularly beneficial for powering edge devices such as IP cameras, VoIP phones, and wireless access points. It supports standard IEEE 802.3af and 802.3at PoE protocols, ensuring compatibility with a wide range of powered devices. The S-110PP is built to withstand harsh environmental conditions, featuring an industrial-grade design that is tested for reliability and durability.

The S-110P-SFP model introduces flexibility with its SFP (Small Form-factor Pluggable) slot, which allows users to customize their connection types by accommodating different SFP transceivers. This feature enables seamless integration into varying network environments, whether requiring fiber or copper connections. The S-110P-SFP also supports a wide range of data rates, making it suitable for high-speed applications.

On the other hand, the S-110P offers an excellent blend of performance and functionality with its compact design. This model is primarily focused on simple and effective media conversion, ensuring reliable data transmission between different media types, such as twisted pair and fiber optics. The S-110P is ideal for users looking to extend their network over long distances while maintaining high performance.

Lastly, the S-110PP-SFP combines the advantages of the previous models, providing both Power over Ethernet capabilities and the versatility of SFP slots. This hybrid approach not only enhances deployment options but also optimizes the use of existing network infrastructure. The S-110PP-SFP caters to businesses looking to modernize their networks with both power and connectivity solutions in a single, convenient package.

In summary, Perle Systems' S-110 series—comprising S-110PP, S-110P-SFP, S-110P, and S-110PP-SFP—offers a comprehensive suite of features. These devices are built for reliability, flexibility, and exceptional performance, addressing the diverse needs of modern network infrastructures. Whether extending network reach, powering devices, or accommodating varied connection types, the S-110 series is an excellent choice for networking professionals.
Top Page Image Contents