Omega Engineering DP3600 Scaling, Programming Group Selection, Decimal point, High Scale

Page 6

Programming Group Selection:

On entering correct passcode, setup procedure starts. The very first step will let you select one of the three groups of parameters that you can program. Three available groups are: 1) SCALING 2) PROGRAM LIMITS 3) PROGRAM SYSTEM. Each group will let you program various parameters as shown below:

SCALING

1.High Scale

2.Low Scale

3.Offset

4.Tare

PROGRAM LIMITS

1.Process Limit1

2.Process Limit2

3.Setup limt 3 for Rate/Process

4.Process Limit 3

5.Setup Limit4 for Process/Deviation

6.Process Limit 4

7.Timer 1 Limit

8.Timer 2 Limit

9.Deadband for limits

9.Limits Normally open/close (1 Thru 4)

10.Limits Latching/Non Latching

11.Audio Alarm On/Off

PROGRAM SYSTEM

1.Display Options

2.Flash Time

3.Engineering units

4.Program Setpoint

5.Remote Tare/Hold

6.Input Type

7.Input Range

Push ^v key to move from one programming group to the next. When a desired group is displayed, push SETUP key to select it.

SCALING

Decimal point:

Decimal point mode is indicated as ‘dp 9999’ (dp stands for DECIMAL POINT). Push ^v key to program decimal point. Each push on the ^v key moves the decimal point to the next position. After 9.999 the display will go to 9999. When proper decimal point position has been obtained push SETUP key to go to the next mode.

High Scale:

High scale mode is indicated by a brief display of the message ‘HI SCLE’ followed by high scale value. The least significant digit (right most digit) will be flashing. The flashing indicates that pushing ^v key will increment or decrement that particular digit. Pushing ^v key once and holding it down will increment the flashing digit. Releasing the ^v key and pushing it again immediately ( and then holding it in) will start decrementing the display. The desired number can be programmed by toggling the ^v key. To move to the next significant digit push <NXT> key, and to increment or decrement it, use ^v key. After obtaining a new high scale value (or to retain the current one) push SETUP key to get to the next mode.

Low Scale:

Low Scale mode is indicated by the display first flashing ‘LO SCLE’ and then the pre-programmed value of low scale. Again, to change the flashing digit value use ^v key. To change any other digit, use <NXT> key to make that digit flash and then use ^v key to change its value. After obtaining a new value (or to retain the present value) push setup key. This will also get you into the next function.

5

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Programmable Process Monitors SET UP Flow Chart MAX. and MIN. Readings Peaks Scaling Offset Tare Limits Specifications External HoldSetup Exit SET UPSetup Entry DescriptionDecimal point ScalingProgramming Group Selection High ScaleProgram Limits Selection of Limit 4 as Process or Deviation Limit Timers 1Configuring Limits Normally open/Normally Closed Relay DeadbandProgram System Input Type Rate Time-BaseRemote Tare/Hold Input RangeSET UP Flow Chart Rate ResettingMAX. and MIN. Readings Peaks TimeProcess Change OffsetTare LimitsProcess Limits Status Alarm OutputsTimer Limits Electro-Mechanical Relay OptionSaving Parameter PowerHold Function Open Collector OptionOutput Connector PIN Assignment PIN no DescriptionTrouble Shooting Factory default settings for voltage, current and millivoltError Messages Panel Cutout Dimensions Mounting

DP3600 specifications

Omega Engineering has long been a trusted name in the realm of industrial instrumentation, and their DP3600 series has set a high standard in differential pressure measurement. The DP3600 is celebrated for its robustness and versatility, making it a reliable choice for a variety of applications across industries such as HVAC, water treatment, and chemical processing.

One of the standout features of the DP3600 is its advanced microprocessor-based technology. This enables highly accurate measurements and ensures that the device can effectively manage multiple pressure inputs. The DP3600 operates on a wide measurement range, accommodating both high and low differential pressure readings with exceptional precision. It is designed to handle pressures from -500 to +500 inHg, making it suitable for even the most demanding environments.

The device is characterized by its user-friendly interface, which includes a clear digital display that shows real-time readings. This feature not only enhances usability but also ensures that operators can quickly interpret data without extensive training. Furthermore, the DP3600 offers a variety of output options including analog and digital signals, allowing for seamless integration with existing systems.

Durability is another key characteristic of the DP3600. Constructed to endure harsh conditions, it boasts an IP65 rating for dust and water resistance, making it suitable for use in outdoor and high-moisture environments. The unit is also designed for easy installation and maintenance, which helps reduce downtime and operational costs.

Moreover, the DP3600 series includes built-in safety features, such as over-range protection, ensuring that the device remains operational even in extreme conditions. With options for various materials and configurations, users can customize the DP3600 to better fit their application's requirements.

In summary, the Omega Engineering DP3600 series is an advanced differential pressure device that excels in accuracy, versatility, and durability. Its microprocessor-driven capabilities, broad measurement range, and user-friendly interface make it a valuable tool for professionals seeking reliable pressure measurement solutions in challenging environments. With these features, the DP3600 continues to be a preferred choice for industries requiring precise monitoring and control of differential pressure.
Top Page Image Contents