Omega Engineering DP3600 user manual Rate Time-Base, Remote Tare/Hold, Input Type, Input Range

Page 10

Rate Time-Base:

This step is for programming time-base for calculation of Rate. Units of time-base are seconds. Again, the active digit will be flashing. To change the value, push ^v key. To activate another digit for change, use <NXT> key. On finishing, push SETUP key.

Remote Tare/Hold:

Remote Tare/Hold feature lets you select between the remote switch being used for resetting tare or holding the reading on the display. The display will read 'RT TARE' (for remote Tare) or 'RT HOLD' ( for remote display hold feature ). To get the alternate mode push ^v key. Else push SETUP key and this will get you into the next function.

Input Type:

The step after remote Tare/Hold is selecting the input type. The display will first read ‘IP TYPE’ followed by the current selection. Various input types are:

i)

CURRENT

4-20MA Signal

ii)

VOLTAGE

0-10Vdc, 0-5Vdc etc.

iii) LO VOLT

0-100mv etc.

To make a selection push ^v key. After selection push SETUP key to go to the next step.

Input Range:

The following step is the last step in this process. This is where you program the input range of your signal. On entering this mode, the display will first read "IP RNGE" (for input range) followed by the indication of current input range. Following RANGE values should be entered for various inputs:

INPUT TYPE

INPUT RANGE

PROGRAMMED VALUE

VOLTAGE

0-10VDC Signal

10.000

VOLTAGE

0-5VDC Signal

5.000

CURRENT

4-20ma Loop Current

20.00

LO VOLT

0-100 Millivolt Signal

100.0

If the end user recalibrates any of the process inputs to different values he/she must enter new values here.

NOTE: THE INPUT TYPE IS SET ACCORDING TO THE MODEL ORDERED. SIMPLY MAKING A SELECTION WILL NOT CONVERT THE UNIT FROM A CURRENT TO A VOLTAGE OR A MILLIVOLT UNIT. THIS IS A HARDWARE CHANGE AND MUST BE SELECTED AT THE TIME OF PLACING THE ORDER.

After entering the desired input range, push the SETUP key. This will take us back to the very beginning of setup mode with the display reading SETUP briefly and then SCALING. To exit at this point push and hold RESET key till the display shows ‘SAVING’.

9

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Programmable Process Monitors SET UP Flow Chart MAX. and MIN. Readings Peaks Scaling Offset Tare Limits Specifications External HoldSetup Exit SET UPSetup Entry DescriptionDecimal point ScalingProgramming Group Selection High ScaleProgram Limits Selection of Limit 4 as Process or Deviation Limit Timers 1Configuring Limits Normally open/Normally Closed Relay DeadbandProgram System Input Type Rate Time-BaseRemote Tare/Hold Input RangeSET UP Flow Chart Rate ResettingMAX. and MIN. Readings Peaks TimeProcess Change OffsetLimits TareProcess Limits Status Alarm OutputsTimer Limits Electro-Mechanical Relay OptionSaving Parameter PowerHold Function Open Collector OptionOutput Connector PIN Assignment PIN no DescriptionFactory default settings for voltage, current and millivolt Trouble ShootingError Messages Panel Cutout Dimensions Mounting

DP3600 specifications

Omega Engineering has long been a trusted name in the realm of industrial instrumentation, and their DP3600 series has set a high standard in differential pressure measurement. The DP3600 is celebrated for its robustness and versatility, making it a reliable choice for a variety of applications across industries such as HVAC, water treatment, and chemical processing.

One of the standout features of the DP3600 is its advanced microprocessor-based technology. This enables highly accurate measurements and ensures that the device can effectively manage multiple pressure inputs. The DP3600 operates on a wide measurement range, accommodating both high and low differential pressure readings with exceptional precision. It is designed to handle pressures from -500 to +500 inHg, making it suitable for even the most demanding environments.

The device is characterized by its user-friendly interface, which includes a clear digital display that shows real-time readings. This feature not only enhances usability but also ensures that operators can quickly interpret data without extensive training. Furthermore, the DP3600 offers a variety of output options including analog and digital signals, allowing for seamless integration with existing systems.

Durability is another key characteristic of the DP3600. Constructed to endure harsh conditions, it boasts an IP65 rating for dust and water resistance, making it suitable for use in outdoor and high-moisture environments. The unit is also designed for easy installation and maintenance, which helps reduce downtime and operational costs.

Moreover, the DP3600 series includes built-in safety features, such as over-range protection, ensuring that the device remains operational even in extreme conditions. With options for various materials and configurations, users can customize the DP3600 to better fit their application's requirements.

In summary, the Omega Engineering DP3600 series is an advanced differential pressure device that excels in accuracy, versatility, and durability. Its microprocessor-driven capabilities, broad measurement range, and user-friendly interface make it a valuable tool for professionals seeking reliable pressure measurement solutions in challenging environments. With these features, the DP3600 continues to be a preferred choice for industries requiring precise monitoring and control of differential pressure.
Top Page Image Contents