Omnitron Systems Technology GX/TM2 user manual Installing the Module and Connecting Cables

Page 10

3.3INSTALLING THE MODULE AND CONNECTING CABLES

PI

a.Carefully slide the module into an open slot in the chassis. Align the module with the installation guides and ensure that the module is firmly seated against the backplane. Secure the module by fastening the front panel thumbscrew (push in and turn clockwise to tighten) to the chassis front. Verify the “Pwr” LED is ON (indicating the chassis is powered).

SA

a.The GX/TM2 standalone Network Interface Device (NID) is available in tabletop and wall-mounting models. For wall-mounting, attach the NID to a wall, backboard or other flat surfaces. For tabletop installation, place the unit on a flat and level surface. Attach the rubber feet to the bottom of the NID to prevent the unit from sliding. Make sure the unit is placed in a safe, dry and secure location.

To power the unit using the AC/DC adapter, connect the AC/DC adapter to the AC outlet. Then connect the barrel plug at the end of the wire on the AC/DC adapter to the 2.5mm DC barrel connector (center-positive) on the unit. Confirm that the unit has powered up properly by checking the power status LED located on the front of the unit.

To power the unit using a DC power source, prepare a power cable using a two-conductor insulated wire (not supplied) with a 14 AWG gauge minimum. Cut the power cable to the length required. Strip approximately 3/8 of an inch of insulation from the power cable wires. Connect the power cables to the standalone unit by fastening the stripped ends to the DC power connector.

Connect the power wires to the DC power source. The Power LED should indicate the presence of power.

WARNING: Note the wire colors used in making the positive, negative and ground connections. Use the same color assignment for the connection at the DC power source.

NOTE: If mounting with a safety ground attachment, use the safety ground screw at the rear of the unit.

PI

SA

b.When using a GX/TM2 SFP model, insert the SFP Fiber transceiver into the Port 1 SFP receptacle on the GX/TM2.

NOTE: The release latch of the SFP Fiber transceiver must be in the closed (up) position before insertion.

c.Connect the UTP port via a Category 5 or better cable to a 10BASE-T, 100BASE-TX or 1000BASE-T Ethernet device.

d.Connect the appropriate multimode or single-mode fiber cable to the fiber port of the installed module. It is important to ensure that the transmit (TX) is attached to the receive side of the device at the other end and the receive (RX) is attached to the transmit side. Single-fiber (SF) media converter models operate in pairs. The TX wavelength must match the RX wavelength at the other end and the RX wavelength must match the TX wavelength at the other end.

Page 10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Standalone and PLUG-IN Module Table of Contents Overview SA Standalone Plug-InPort Structure Installation Procedure B B B B B B BConfiguring DIP-SWITCHES 1.2 SW2 UTP Auto/Manual Negotiation AN/Man 1.3 SW3 UTP Speed Gigabit/10-100 1000/10-100 This DIP-switch is for factory use only Installing the Module and Connecting Cables Passwords Management Options screen will be displayed GX/TM2 Setting IP Parameters as Dhcp Client Setting GX/TM2 Passwords Setting Snmp Preferences Setting SNMPv1/v2c Read and Write Community Names Setting the Snmp Trap IP Host Addresses Enabling/Disabling Soft-switch Reload Access the GX/TM2 Remotely Updating the GX/TM2 Firmware via the Serial Console Port Updating the GX/TM2 Firmware via FTP Verifying Operation Detailed Module Configuration NMMGX/TM2 LED UTP FDXModule Management Mode Configuration Setting 17 Port Configuration UTP Layer 2 Control Protocol Filter SFP Information A167EC500000 5 802.3ah Parameters Page OUI Port Vlan Page Tagged Vlan Pvid BP aUTP BP a BP B Vlan ID VIDVlan Table is Empty Vlan ID +1 Vlan ID CNode Loopback To refresh the Port Statistic screen, press Enter GX/TM2 Specifications Cable TypesTroubleshooting Guide Possible CausesUTP Issues Warranty Limitation of Warranty

GX/TM2 specifications

Omnitron Systems Technology has long been at the forefront of networking solutions designed to enhance communication across various industries. One of their standout products is the GX/TM2, an innovative device that caters to the evolving demands of modern network environments.

The GX/TM2 is a robust and flexible media converter designed to facilitate seamless integration between different types of network media. This device supports a wide range of Ethernet technologies, making it an ideal choice for organizations looking to bridge fiber optic and copper connections. It is particularly valuable for enterprises that need to expand or upgrade their network architecture without overhauling existing infrastructure.

One of the main features of the GX/TM2 is its compatibility with both Fast Ethernet (10/100 Mbps) and Gigabit Ethernet (10/100/1000 Mbps). This versatility allows users to choose the speed that best suits their operational needs, ensuring they can accommodate varying bandwidth requirements. Additionally, the device supports a range of fiber types, including multimode and single-mode fibers, extending transmission distances significantly—some models can achieve reach up to 120 kilometers.

The GX/TM2 incorporates advanced technologies, including auto-negotiation, which automatically detects and configures the parameters of the connected network. This feature minimizes setup time and reduces the risk of manual configuration errors. Another valuable technology is the built-in management interface, which allows for real-time monitoring and diagnostics, helping network administrators maintain optimal performance and troubleshoot issues quickly.

Moreover, the GX/TM2 is designed with reliability in mind. It features robust hardware construction, which makes it resistant to environmental factors, ensuring dependable operation in diverse settings. Its compact form factor and modular design make it easy to deploy and integrate into existing network systems, optimizing space and performance.

Overall, the Omnitron GX/TM2 stands out as a comprehensive solution for organizations seeking to enhance their network capabilities. With its advanced features, wide compatibility, and emphasis on reliability, it empowers businesses to build efficient, high-performance networks that can adapt to changing technological landscapes. Whether for upgrading legacy systems or deploying new network expansions, the GX/TM2 provides the flexibility and performance necessary for modern connectivity demands.
Top Page Image Contents