Omnitron Systems Technology GX/TM2 user manual This DIP-switch is for factory use only

Page 9

For detailed information on the operation of the different Link Modes, download the application note “iConverter Link Modes” available on Omnitron’s web page:

http://www.omnitron-systems.com/downloads.php

3.2.2Board-Mounted Bank 2 Settings

PI

DIP-switch Bank 2 is available on the plug-in module only.

Switch

Left (Factory Default)

Right

 

 

 

SW1

A-DS:Port A Disabled

A-EN:Port A Enabled

 

 

 

SW2

B-DS:Port B Disabled

B-EN:Port B Enabled

 

 

 

SW3

M/SL:

SL:

Master/Slave Auto-Select

Slave-Mode Only

 

SW4

Reserved

Reserved

 

 

 

3.2.2.1SW1 - Backplane Port A Enabled “A-DS/A-EN”

When the DIP-switch is in the Left “A-DS” position (factory default), Backplane Port A of the GX/TM2 is isolated from the chassis Backplane. When the DIP-switch is in the Right “A-EN” position, Backplane Port A of the GX/TM2 is enabled. This port allows Ethernet Backplane connectivity to an adjacent module via the chassis Backplane Port A. See the backplane illustrations in Section 2.1.3.

3.2.2.2SW2 - Backplane Port B Enabled “B-DS/B-EN”

When the DIP-switch is in the Left “B-DS” position (factory default), Backplane Port B is isolated from the chassis Backplane. When the DIP-switch is in the Right “B-EN” position, Backplane Port B is enabled. This port allows Ethernet Backplane connectivity to an adjacent module via the chassis Backplane Port B. See the backplane illustrations in Section 2.1.3.

3.2.2.3SW4 - Master/Slave Auto-Select and Slave-Only “M/SL / SL

When multiple management modules such as the iConverter Network Management Module (NMM) and the GX/TM2 (or multiple self-managed modules such as the 10/100M) are installed in the same chassis, only one management module can act as the chassis master. The master management module has the ability to make changes to the settings of the other modules in the chassis, while the slave management modules cannot make the changes. If an NMM is installed in the chassis, the NMM will always be the master, otherwise the lowest slot number with a management module installed will become chassis master.

When this DIP-switch is in the Left “M/SL” position (factory default), the assignment of mastership is automatically negotiated by the installed management modules. To designate a specific management module as the master when no NMM is installed in the chassis, set the DIP-switch on the master module to the Left “M/SL” position, and set the other installed management modules’ DIP-switches to the Right “SL” position to enable Slave-Only mode.

Only the chassis master can change configuration settings of other modules.

3.2.2.4SW4 - Reserved

This DIP-switch is for factory use only.

NOTE: DIP-switch marked Reserved must be kept in the Left (factory default) position.

Page 9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Standalone and PLUG-IN Module Table of Contents SA Standalone Plug-In OverviewPort Structure B B B B B B B Installation ProcedureConfiguring DIP-SWITCHES 1.2 SW2 UTP Auto/Manual Negotiation AN/Man 1.3 SW3 UTP Speed Gigabit/10-100 1000/10-100 This DIP-switch is for factory use only Installing the Module and Connecting Cables Passwords Management Options screen will be displayed GX/TM2 Setting IP Parameters as Dhcp Client Setting GX/TM2 Passwords Setting Snmp Preferences Setting SNMPv1/v2c Read and Write Community Names Setting the Snmp Trap IP Host Addresses Enabling/Disabling Soft-switch Reload Access the GX/TM2 Remotely Updating the GX/TM2 Firmware via the Serial Console Port Updating the GX/TM2 Firmware via FTP Verifying Operation NMM Detailed Module ConfigurationGX/TM2 UTP FDX LEDModule Management Mode Configuration Setting 17 Port Configuration UTP Layer 2 Control Protocol Filter SFP Information A167EC500000 5 802.3ah Parameters Page OUI Port Vlan Page Tagged Vlan BP a PvidVlan ID VID UTP BP a BP BVlan Table is Empty Vlan ID +1 Vlan ID CNode Loopback To refresh the Port Statistic screen, press Enter Cable Types GX/TM2 SpecificationsPossible Causes Troubleshooting GuideUTP Issues Limitation of Warranty Warranty

GX/TM2 specifications

Omnitron Systems Technology has long been at the forefront of networking solutions designed to enhance communication across various industries. One of their standout products is the GX/TM2, an innovative device that caters to the evolving demands of modern network environments.

The GX/TM2 is a robust and flexible media converter designed to facilitate seamless integration between different types of network media. This device supports a wide range of Ethernet technologies, making it an ideal choice for organizations looking to bridge fiber optic and copper connections. It is particularly valuable for enterprises that need to expand or upgrade their network architecture without overhauling existing infrastructure.

One of the main features of the GX/TM2 is its compatibility with both Fast Ethernet (10/100 Mbps) and Gigabit Ethernet (10/100/1000 Mbps). This versatility allows users to choose the speed that best suits their operational needs, ensuring they can accommodate varying bandwidth requirements. Additionally, the device supports a range of fiber types, including multimode and single-mode fibers, extending transmission distances significantly—some models can achieve reach up to 120 kilometers.

The GX/TM2 incorporates advanced technologies, including auto-negotiation, which automatically detects and configures the parameters of the connected network. This feature minimizes setup time and reduces the risk of manual configuration errors. Another valuable technology is the built-in management interface, which allows for real-time monitoring and diagnostics, helping network administrators maintain optimal performance and troubleshoot issues quickly.

Moreover, the GX/TM2 is designed with reliability in mind. It features robust hardware construction, which makes it resistant to environmental factors, ensuring dependable operation in diverse settings. Its compact form factor and modular design make it easy to deploy and integrate into existing network systems, optimizing space and performance.

Overall, the Omnitron GX/TM2 stands out as a comprehensive solution for organizations seeking to enhance their network capabilities. With its advanced features, wide compatibility, and emphasis on reliability, it empowers businesses to build efficient, high-performance networks that can adapt to changing technological landscapes. Whether for upgrading legacy systems or deploying new network expansions, the GX/TM2 provides the flexibility and performance necessary for modern connectivity demands.
Top Page Image Contents