Omnitron Systems Technology GX/TM2 user manual Troubleshooting Guide, Possible Causes

Page 46

6.0TROUBLESHOOTING GUIDE

6.1OVERVIEW

The GX/TM2 module has several LED indicators available to assist in the determination of problems. Refer to Section 3.5, Verify Operation, for LED definitions.

6.1.1Power Issues

Problem:

The Power LED does not illuminate after installation is complete or no LED indicators are ON

Possible Causes:

A. For standalone modules, confirm that the power supply is connected to both the module and the AC or DC power source. If Power LED is still not illuminated, use a voltmeter and check the voltage of the power source (AC/DC converter used with the standalone unit should measure between 9 -15 VDC no load at the barrel connector).

B. For plug-in module, confirm that the chassis is connected to an AC or DC power source. If the Power LED is still not illuminated, remove the module and verify the operation of other modules in the chassis. If power is present and the module will not turn ON, replace the module.

C. The plug-in module requires ~ 3.6 watts (3.3VDC @ 1.1 amps) for normal operation. The AC Power Supply in a 19-Module Chassis can supply ~ 60 watts (3.3VDC @ 18amp). A fully loaded 19-Module chassis of GX/TM2 modules will require two power supplies for standard operation. This condition will cause the power LED not to illuminate.

6.1.2Fiber Issues

Problem:

The Fiber Optic link LED does not illuminate after installation is complete.

Possible Causes:

A. Verify the Link Mode selection is set to Link Segment (LS). Until a stable link is established, leave the Link Mode configured for LS. After a Link presence is established, the Link Mode selection can be modified.

B. Confirm that the fiber optic cable is properly connected to the iConverter GX/TM2 and the remote fiber optic device. Connecting the fiber between the Tx of the far end to the Rx on the near end will cause the FO LED on the near end to illuminate (only when the link mode is configured for Link Segment). Completing the connection will cause the far end FO LED to illuminate.

C. Confirm that the fiber cable type matches the fiber transceiver type (multimode, single-mode) on the iConverter GX/TM2.

D. If using a dual-fiber model, confirm that the transmitter (Tx) is attached to the receiver side of its link partner, and that the receiver (Rx) is attached to the transmitter. A optical power meter will assist in determining which cable should be connected to the Tx and Rx of the module. To insure proper operation, a minimum of -30dBm must be present at the fiber optic receiver.

E. If using a single-fiber model, confirm that the Tx wavelength on the iConverter GX/TM2 matches the Rx of the connected fiber optic device. Single-fiber units transmit and receive at different wavelengths (1510nm/1310nm). Verify the model numbers to insure proper compatibility.

Page 46

Page 45 Page 47
Image 46
Page 45 Page 47
Contents Standalone and PLUG-IN Module Table of Contents Overview SA Standalone Plug-InPort Structure Installation Procedure B B B B B B BConfiguring DIP-SWITCHES 1.2 SW2 UTP Auto/Manual Negotiation AN/Man 1.3 SW3 UTP Speed Gigabit/10-100 1000/10-100 This DIP-switch is for factory use only Installing the Module and Connecting Cables Passwords Management Options screen will be displayed GX/TM2 Setting IP Parameters as Dhcp Client Setting GX/TM2 Passwords Setting Snmp Preferences Setting SNMPv1/v2c Read and Write Community Names Setting the Snmp Trap IP Host Addresses Enabling/Disabling Soft-switch Reload Access the GX/TM2 Remotely Updating the GX/TM2 Firmware via the Serial Console Port Updating the GX/TM2 Firmware via FTP Verifying Operation Detailed Module Configuration NMMGX/TM2 LED UTP FDXModule Management Mode Configuration Setting 17 Port Configuration UTP Layer 2 Control Protocol Filter SFP Information A167EC500000 5 802.3ah Parameters Page OUI Port Vlan Page Tagged Vlan Pvid BP aUTP BP a BP B Vlan ID VIDVlan Table is Empty Vlan ID +1 Vlan ID CNode Loopback To refresh the Port Statistic screen, press Enter GX/TM2 Specifications Cable TypesTroubleshooting Guide Possible CausesUTP Issues Warranty Limitation of Warranty

GX/TM2 specifications

Omnitron Systems Technology has long been at the forefront of networking solutions designed to enhance communication across various industries. One of their standout products is the GX/TM2, an innovative device that caters to the evolving demands of modern network environments.

The GX/TM2 is a robust and flexible media converter designed to facilitate seamless integration between different types of network media. This device supports a wide range of Ethernet technologies, making it an ideal choice for organizations looking to bridge fiber optic and copper connections. It is particularly valuable for enterprises that need to expand or upgrade their network architecture without overhauling existing infrastructure.

One of the main features of the GX/TM2 is its compatibility with both Fast Ethernet (10/100 Mbps) and Gigabit Ethernet (10/100/1000 Mbps). This versatility allows users to choose the speed that best suits their operational needs, ensuring they can accommodate varying bandwidth requirements. Additionally, the device supports a range of fiber types, including multimode and single-mode fibers, extending transmission distances significantly—some models can achieve reach up to 120 kilometers.

The GX/TM2 incorporates advanced technologies, including auto-negotiation, which automatically detects and configures the parameters of the connected network. This feature minimizes setup time and reduces the risk of manual configuration errors. Another valuable technology is the built-in management interface, which allows for real-time monitoring and diagnostics, helping network administrators maintain optimal performance and troubleshoot issues quickly.

Moreover, the GX/TM2 is designed with reliability in mind. It features robust hardware construction, which makes it resistant to environmental factors, ensuring dependable operation in diverse settings. Its compact form factor and modular design make it easy to deploy and integrate into existing network systems, optimizing space and performance.

Overall, the Omnitron GX/TM2 stands out as a comprehensive solution for organizations seeking to enhance their network capabilities. With its advanced features, wide compatibility, and emphasis on reliability, it empowers businesses to build efficient, high-performance networks that can adapt to changing technological landscapes. Whether for upgrading legacy systems or deploying new network expansions, the GX/TM2 provides the flexibility and performance necessary for modern connectivity demands.
Top Page Image Contents