NETGEAR XAVB5501-100NAS, XAV5501-100NAS user manual Regulatory Compliance Information

Page 28

XAV5501 Powerline AV+ 500 Adapter User Manual

The voltage and current rating of the cable should be greater than the ratings marked on the product.

•To help prevent electric shock, plug the system and peripheral power cables into properly grounded electrical outlets.

•Do not use adapter plugs. If you must use an extension cable, use a three-wire cable with properly grounded plugs.

•Observe extension cable and power strip ratings. Make sure that the total ampere rating f all products plugged into the extension cable or power strip does not exceed 80 percent of the ampere ratings limit for the extension cable or power strip.

•To help protect your system from sudden, transient increases and decreases in electrical power, use a surge suppressor, line conditioner, or uninterruptible power supply (UPS).

•Position system cables and power cables carefully; route cables so that they cannot be stepped on or tripped over. Be sure that nothing rests on any cables.

•Do not modify power cables or plugs.

•Always follow your local and national wiring rules.

Regulatory Compliance Information

This section includes user requirements for operating this product in accordance with National laws for usage of radio spectrum and operation of radio devices. Failure of the end-user to comply with the applicable requirements may result in unlawful operation and adverse action against the end-user by the applicable National regulatory authority.

This product's firmware limits operation to only the channels allowed in a particular Region or Country. Therefore, all options described in this user's guide may not be available in your version of the product.

FCC Requirements for Operation in the United States

FCC Information to User

This product does not contain any user serviceable components and is to be used with approved antennas only. Any product changes or modifications will invalidate all applicable regulatory certifications and approvals

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

FCC Guidelines for Human Exposure

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20 cm between the radiator and your body.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

28 Appendix B. Notification of Compliance

Page 27 Page 29
Image 28
Page 27 Page 29
Contents XAV5501 Powerline AV+ Adapter Technical Support TrademarksStatement of Conditions Revision HistoryContents Installation and Basic Configuration How the Powerline AV+ 500 Adapter Fits in Your NetworkLED and Feature Descriptions Powerline XAV5501 Adapter FeaturesXAV5501 Product Label Model Number Feature Descriptions Installing Your Powerline XAV5501 Adapter Prepare for InstallationConnecting a Powerline AV+ 500 Adapter to the Router Connecting the XAV5501 to a RouterTo add Powerline adapters Adding Adapters to Your NetworkUnderstanding Powerline Network Security Set the Encryption KeyTo set a private encryption key Installing the XAV5501 Powerline Utility To install the XAV5501 Powerline UtilityPowerline Utility Screen Navigate to Start Programs Netgear Netgear Powerline UtilityChange the Name of a Powerline Device Powerline Utility main screenTurn LEDs On or Off To name any Powerline device in your Powerline networkSet Encryption Keys To set the Encryption Key for the Powerline network Set Up Quality of Service QoSClick Apply Security to Selected Devices QoS Setup screen Using the XAV5501 Powerline Utility To prioritize by general application typeAdd a Device to a Powerline Network Reset a Device to Factory SettingsTo reset to factory defaults To add a device from a locally connected computer Security IconClick the Apply Security to Selected Devices button Return to the Default Network Encryption Key Click the Use Default Encryption Key buttonProduct Registration and Support Basic FunctioningLED Troubleshooting Tips LED and Feature TroubleshootingProblems after Changing the Network Encryption Key Technical Specifications Supplemental InformationSafety Information Electromagnetic EmissionsAppendix A. Supplemental Information Netgear Powerline Products Notification of ComplianceRegulatory Compliance Information FCC Requirements for Operation in the United StatesFCC Declaration Of Conformity GPL License Agreement Index Index
Top Page Image Contents