Miller Electric Remote Operator Interface manual Introduction, Installation, Specifications

Page 13

SECTION 3 − INTRODUCTION

3-1.	Specifications

Type of Input		Welding Power	Wire Feed Speed Range	Wire Diameter	Welding Circuit	Overall	Weight
Power		Source Type	Wire Feed Speed Range	Range	Rating	Dimensions	Weight
Power		Source Type		Range	Rating	Dimensions

40 Volts DC		Axcess Series	Standard: 40 To 1400 ipm (1.0	.035 To 1/16 in	100 Volts,	Length: 7 in (178	11 lb
10 Amperes			To 35.6 mpm)	(0.8 To 1.6 mm)	750 Amperes,	mm)	(5 kg)
					100% Duty	Width: 7 in
				Max Spool	Cycle	Width: 7 in
				Max Spool	Cycle	(178 mm)
				Weight: 60 lb (27		(178 mm)
				Weight: 60 lb (27		Height: 12 in
				kg)		Height: 12 in
						(305 mm)

SECTION 4 − INSTALLATION

4-1. Mounting Plate Hole Layout

4in

(102 mm)

7/32 in (5.6 mm) Dia.

(4 holes)

1-3/4 in	3 in	1-3/4 in
(44 mm)	(76 mm)	(44 mm)	Ref. 200 553-A
			Ref. 200 553-A

OM-217 834 Page 9

Image 13

Contents Processes OM-217 834GDescription File Advanced Manufacturing SystemsFrom Miller to You Table of Contents Page Marks a special safety message Symbol UsageArc Welding Hazards Electric Shock can killWelding can cause fire or explosion ARC Rays can burn eyes and skinFlying Metal can injure eyes Buildup of GAS can injure or killCalifornia Proposition 65 Warnings EMF Information Principal Safety StandardsAbout Pacemakers LES Fumées ET LES GAZ peuvent être dangereux UNE Décharge Électrique peut entraîner la mortIndique un message de sécurité particulier Incendie ou une explosion LE Soudage peut provoquer unDES Particules Volantes peuvent blesser les yeux DES Pièces Chaudes peuvent provoquer des brûlures gravesLA Chute DE L’APPAREIL peut blesser Risque D’INCENDIE OU D’EXPLO’EMPLOI Excessif peut SUR DES Organes Mobiles peuvent provoquer des blessuresEn ce qui concerne les stimulateurs cardiaques Principales normes de sécuritéSpecifications − Installation− Introduction Mounting Plate Hole LayoutTurn Off and disconnect input power Installing Insulator KitConnection Diagram Remote Operator Interface And Wire Drive InstallationPin Network Receptacle Information Rear Panel ConnectionsGun Recommendation Table Pin InformationDual Schedule Switch Option Power Source Display At Power UpPower Source Upper Display Lower Display Voltage Range Operational Terms − OperationPower Switch Front Panel Sections See Section Program Volts Time Arc AdjustSee SectionProgram Push Button Volts Arc AdjustUpper Display Lower Display Adjust Knob Feeder Set Up Push ButtonSequence Trigger Control Trigger Hold Feeder Set Up CO2 Process Set Up Push ButtonJog/Purge Jog/Purge switch provides the following functionsRST Reset ModeSequence Parameters In a Program − Setting Sequence ParametersSequence Parameters Routine Maintenance − MaintenanceDisconnect power Before maintainingERR ARC DiagnosticsIndicates a trigger Closed errorOM-217 834 Circuit Diagram − Electrical Diagram214 842-E Remote Operator Interface − Parts ListPC1 Page Page Page Support ServiceMiller Electric Mfg. Co Owner’s Record

SECTION 3 − INTRODUCTION

Specifications

Max Spool

Cycle

SECTION 4 − INSTALLATION

4-1. Mounting Plate Hole Layout