Miller Electric Remote Operator Interface manual Feeder Set Up Push Button, Adjust Knob

Page 23

5-7. Feeder Set Up Push Button

3

4 Sequence

Trigger Control

Trigger Hold

2

Feeder Set Up

 

Start

Crater

 

Time

Time

1

Preflow

 

 

 

Postflow

 

Time

 

Time

 

 

 

 

 

 

 

 

 

 

 

 

 

Sequence Diagram

1Feeder Set Up Push Button LED

2Feeder Set Up Push Button

•Press button to choose Sequence. Feeder Set Up push-button LED will illuminate.

3 Sequence LED

•When the Feeder Set Up button is pressed once, the Sequence LED will illuminate and the upper display will show sequence options. Use the Adjust knob to select PRE (preflow), STRT (start), CRTR (crater), or POST (postflow).

•Press the lower display push button and the Lower Display push-button LED will illuminate as well as the lower display. The Time LED will automatically begin flashing indicating that a time value can be entered by turning the Adjust knob. By entering a time value the sequence state will become active. To turn off a sequence state, change the time value to OFF. To step back for selecting another sequence option, press

the Upper Display push button.

•The Sequence option STRT and CRTR will have additional parameter settings. By pushing the Lower Display push button a second time, while STRT or CRTR appear in the upper display, allows entering voltage (MIG) or Arc Adjust [Pulse, Accu-pulse, or RMD (optional)]. Use the Adjust knob to change the values indicated by the flashing LED for either Volts or Arc Adjust. Pressing the Lower Display push button a third time will activate the WFS setting for either STRT or CRTR and the WFS LED will begin flash- ing. Use the Adjust knob to change the WFS value.

•Pressing the Feeder Set Up button two more times will exit the Sequence menu and return the system to standby mode.

4 Trigger Control LED

•Press the Feeder Set Up button twice and the Trigger Control LED will illuminate, and the upper display will show the different trig-

ger control selections. Use the Adjust knob to cycle through the trigger control methods as follows: DS, TH, TDS, TPS, and 4T (see Section 5-1for definitions). The lower dis- play will show the current state of each trig- ger control method as being on or off. Not all trigger control methods are compatible with each other, therefore, turning on certain trig- ger selections will cause other trigger selec- tions to turn off.

•Press the lower display push button to illu- minate the push-button LED and enable the use of the Adjust knob to allow turning se- lected trigger control methods on or off. If trigger hold is set to on, the Trigger Hold LED will illuminate.

.Trigger Hold is automatically set to On

with the 4T trigger selection. This is part of the 4T function.

•Press the Feeder Set Up button a third time to cycle back to standby mode.

5-8. Adjust Knob

1 Adjust Knob

The Adjust knob is used to change functions and parameters. Refer to the front panel sections for information regarding use of this control.

1

Adjust

OM-217 834 Page 19

Page 22 Page 24
Image 23
Page 22 Page 24
Contents File Advanced Manufacturing Systems OM-217 834GProcesses DescriptionFrom Miller to You Table of Contents Page Electric Shock can kill Symbol UsageMarks a special safety message Arc Welding HazardsBuildup of GAS can injure or kill ARC Rays can burn eyes and skinWelding can cause fire or explosion Flying Metal can injure eyesCalifornia Proposition 65 Warnings About Pacemakers Principal Safety StandardsEMF Information Indique un message de sécurité particulier UNE Décharge Électrique peut entraîner la mortLES Fumées ET LES GAZ peuvent être dangereux DES Pièces Chaudes peuvent provoquer des brûlures graves LE Soudage peut provoquer unIncendie ou une explosion DES Particules Volantes peuvent blesser les yeuxDES Organes Mobiles peuvent provoquer des blessures Risque D’INCENDIE OU D’EXPLOLA Chute DE L’APPAREIL peut blesser ’EMPLOI Excessif peut SUREn ce qui concerne les stimulateurs cardiaques Principales normes de sécuritéMounting Plate Hole Layout − InstallationSpecifications − IntroductionTurn Off and disconnect input power Installing Insulator KitConnection Diagram Remote Operator Interface And Wire Drive InstallationPin Information Rear Panel ConnectionsPin Network Receptacle Information Gun Recommendation TablePower Source Upper Display Lower Display Voltage Range Power Source Display At Power UpDual Schedule Switch Option Operational Terms − OperationPower Switch Section See Section Program Volts Time Arc AdjustFront Panel Sections SeeUpper Display Volts Arc AdjustProgram Push Button Lower Display Sequence Trigger Control Trigger Hold Feeder Set Up Feeder Set Up Push ButtonAdjust Knob CO2 Process Set Up Push ButtonJog/Purge Jog/Purge switch provides the following functionsRST Reset ModeSequence Parameters − Setting Sequence ParametersSequence Parameters In a Program Before maintaining − MaintenanceRoutine Maintenance Disconnect powerERR ARC DiagnosticsIndicates a trigger Closed errorOM-217 834 Circuit Diagram − Electrical Diagram214 842-E Remote Operator Interface − Parts ListPC1 Page Page Page Support ServiceMiller Electric Mfg. Co Owner’s Record
Top Page Image Contents