Multi-Tech Systems MT2834ZDX manual Contents

Page 3

	Table of Contents
Contents
Chapter 1 – Introduction and Installation	4
Getting Started	4
Safety Warnings	4
We Supply	4
Features	4
Modem Installation	5
Step 1: Attach the Self-Adhesive Feet	5
Step 2: Connect the Modem to Your System	5
Step 3: Install the Modem Driver	6
Step 4: Install Data Communications Software	6
Removing Your Old Modem from Windows	6
Chapter 2 – Operation	7
Front Panel	7
Chapter 3 – AT Commands, S-Registers and Result Codes	8
AT Commands	8
S-Registers	18
Register Unit Range Default Description	18
Result Codes	19
Chapter 4 – Troubleshooting	20
Appendix A – Regulatory Compliance	24
Regulatory Compliance	24
Regulatory Requirements for the United States	24
Regulatory Requirements for Canada	27
Appendix B – Technical Specifications	29
Appendix C – Warranty and Service	30
Multi-Tech Warranty Statement	30
Repair Procedures for U.S. and Canadian Customers	30
Repair Procedures for International Customers (Outside U.S.A. and Canada)	31
Repair Procedures for International Distributors	31
Replacement Parts	31
Appendix D - Waste Electrical and Electronic Equipment (WEEE) Statement	32
Index	33

Multi-Tech Systems, Inc. MT2834ZDX User's Guide

3

Image 3

Contents MT2834ZDX-Series External Data/Fax Modem Users Guide User Guide MT2834ZDX-Series S000309C Rev. C Contents Getting Started Introduction InstallationSafety Warnings FeaturesModem Installation Attach the Self-Adhesive FeetConnect the Modem to Your System Install the Modem Driver Install Data Communications SoftwareRemoving Your Old Modem from Windows Speed Indicator Blink Rates OperationFront Panel AT Commands AT Commands, S- Registers and Result CodesCDn Cleardown at Disconnect $BAn Baud AdjustDCn AT Command Control Carrier Detect ControlDPn Read Line Probe Data En Echo Command Mode CharactersEn V.42 Error Correction Modes En Non-Error Correction Mode Flow ControlFn Echo Frequency Canceller Offset Compensation $En V.42 Error Correction at 300 bpsLoad Default Configurations $Fn Enable/Disable Auto-Reliable Fallback CharacterInquire Product Codes List Commands#L n V.42 Mode Selection in Originate Mode $H n Help ScreensNdNe. .. Number Linking Result Codes Enable/Disable$MBn Modem Baud Rate Nd Dial a Stored NumberRFn CTS/RTS Interaction Control Rn Clear to Send ControlRAn Asymmetrical Bit Rate RDn Square Wave Ring DetectTone-Dial Tn Respond to Remote Digital Loopback SignalSFn DSR/CD Interaction Control $SBn Serial Port Baud RateXn Result Codes and Call Progress Selection Wn Store ConfigurationModem Reset Return to Command ModeAtcr Remote Configuration Escape Sequence +++ATCR Escape CodeBreakatcr Escape Sequence Registers Register Unit Range Default DescriptionTerse Verbose Result CodesNone of the LEDs Light When the Modem Is On TroubleshootingModem Dials But Cannot Connect Modem Disconnects While Online There Are Garbage Characters on the Monitor Appendix a Regulatory Compliance Regulatory ComplianceFCC CFR47 Part 15 Regulation FCC CFR47 Part 68 Telecom USAAAEQ##Txxxx Current Requirements for Label Content and FormatRegulatory Requirements for Canada IC XXXXXX-ZZZZZZZZ Where Industry CanadaTransmit Level -13 dBm Frequency Stability +/-0.01% Appendix B Technical SpecificationsCommand Buffer 60 characters Manual Control Power switchAppendix C Warranty and Service Multi-Tech Warranty StatementRepair Procedures for U.S. and Canadian Customers Repair Procedures for International Distributors Replacement PartsOnline Warranty Registration About the Internet July Index AT CommandsNone of the LEDs light when the modem is on

Related manuals

Manual 33 pages 38.04 Kb