Multi-Tech Systems MT9234ZBA-V manual Installation, Safety Warnings, Change the Internal Jumpers

Page 6

Chapter 2 – Installation

Chapter 2 – Installation

This chapter shows you step-by-step how to set up your Multi-Tech MT9234ZBA modem.

Safety Warnings

•Use this product only with UL- and CUL-listed computers (U.S.A. and Canada)

•To reduce the risk of fire, use only 26 AWG (.41mm) or larger telephone wiring.

•Never install telephone wiring during a lightning storm.

•Never install a telephone jack in a wet location unless the jack is specifically designed for wet locations.

•Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface.

•Use caution when installing or modifying telephone lines.

•Avoid using a telephone during an electrical storm; there is a risk of electrical shock from lightning.

•Do not use a telephone in the vicinity of a gas leak.

•This product must be disconnected from the telephone network interface when servicing.

Step 1: Change the Internal Jumpers

This step is required only if:

•You intend to use the modem on a leased line.

•You intend to add a monophonic external speaker to your modem with the voice option. No changes are needed for stereo.

This will require you to open the modem and move one or more jumpers on the modem’s printed circuit board. Warning: The following procedure must be performed by authorized service personnel.

Caution: The circuit board can be harmed by static electricity. Before you open the case, touch a grounded object, such as the metal chassis of your computer, to discharge any static electricity in your body, then touch the metal shell of the modem’s RS-232 connector to ensure that there is no voltage difference between you and the modem.

Opening the Modem

1.If the modem is connected, turn it off and remove all connecting cables (including the power and line cables).

2.Turn the modem upside down.

3.On the bottom of the modem are two screws, which hold the case together. Remove both screws and set them aside.

4.Turn the modem right side up.

5.Before touching anything inside the modem case, discharge any static in your body by touching a piece of grounded metal such as the computer chassis. Electrostatic discharge (ESD) is the release of stored static electricity that can damage electrical circuitry or components. Static electricity is often stored in your body, and discharged when you come in contact with an object of a different potential.

6.Perform the procedure below described in this section only at an ESD workstation using an antistatic wrist strap. If such a station is not available, you can provide some ESD protection by wearing an antistatic wrist strap and attaching it to a metal ground screw (lug).

7.Remove the top part of the modem case.

8.To close the modem, reverse Steps 1–5.

6

Multi-Tech Systems, Inc. MT9234ZBA-Series User Guide (S000387C)

Page 5 Page 7
Image 6
Page 5 Page 7
Contents MultiModem ZBA Patents PN S000387C, Version C CopyrightTrademarks World HeadquartersContents Features AT Commands InfoIntroduction Technical Specifications CE MarkChange the Internal Jumpers InstallationSafety Warnings Opening the ModemChanging the Voice Jumper Connect the Modem to Your PC Install the Modem Driver Connect the Modem to the AC Power OutletPower-On Test Windows InstallerPage Using AT Commands to Configure Your Modem Configure the Modem for Your Country or RegionUsing the Global Wizard to Configure Your Modem Click Initial Setup and Country/Region SelectionOperation SetupConnecting to the Internet About the Front PanelRemote Configuration Changing the Setup PasswordChanging the Remote Escape Character Changing the Setup Password Callback SecurityTurning Callback Security On and Off Setting Callback Security Message Parity Assigning Callback Passwords and Phone NumbersCalling Procedures Password-Only CallbackNumber-Entry Callback Extension-Entry Callback Direct ConnectionCallback Security Commands Callback Assignments FormTroubleshooting None of the Indicators LightModem Does Not Respond to Commands Modem Cannot Connect When Dialing Page Modem Doesn’t Work with Caller ID Data Is Being LostThere Are Garbage Characters on the Monitor Fax and Data Software Can’t Run at the Same TimeIdentify the Modem Firmware Download the Upgrade FileAppendix a Upgrading the Modem’s Firmware Identify the Current Firmware VersionRestore Your Parameters Extract the Upgrade FilesUpgrade the Modem’s Firmware Clear Your Stored ParametersAppendix B Regulatory Compliance FCC Part 15 RegulationFCC Part 68 Telecom Industry Canada EMC, Safety and R&TTE Directive ComplianceCanadian Limitations Notice Thailand ApprovalNew Zealand Telecom Warning Notice South African StatementJapan Requirements Brazil Special Cable for MT9234ZBA model only Special phone cable is required for regulatory complianceAppendix C Environmental Information Weee Waste Electrical and Electronic Equipment StatementReach Statement Appendix C Environmental Info Rohs HT/TS Substance Concentration CR6+Appendix D Installing a Modem under Linux Appendix E Connecting to a Cisco Router Configure the Modem for your Country or RegionConfigure for Callback Security in Direct Connect Mode Console Port Final Setup Remote ConfigurationConsole Port Connections AT commands Index
Related manuals
Manual 38 pages 57.14 Kb Manual 35 pages 61.01 Kb

MT9234ZBA-V, MT9234ZBA specifications

Multi-Tech Systems has long been a trusted name in the field of communication technology, and its MT9234ZBA and MT9234ZBA-V modem products exemplify the company's commitment to delivering robust and reliable connectivity solutions. These modems are ideal for a range of applications, including telephony, data communication, and remote monitoring, making them a versatile choice for both personal and professional use.

One of the standout features of the MT9234ZBA and MT9234ZBA-V is their high-speed data transmission capabilities. Both models support data rates of up to 56 Kbps, ensuring efficient and swift data transfer for various applications. This allows users to experience minimal latency during downloads and uploads, appealing to those who depend on timely and reliable data delivery.

These modems utilize advanced technologies, such as V.92 and V.90 protocols, which enable users to benefit from features like quick connect, thereby reducing the time it takes to establish a connection. Additionally, the modems support both analog and digital lines, making them adaptable for different environments and infrastructures.

Another notable characteristic of the MT9234ZBA and MT9234ZBA-V modems is their compatibility with a wide range of operating systems, including various versions of Windows, Linux, and Mac OS. This cross-platform support ensures that users can easily integrate these modems into their existing software environments without encountering significant compatibility issues.

The design and construction of these modems are also worth mentioning. They are compact and lightweight, making them easy to install and reposition as needed. Their robust construction ensures longevity, which is crucial for users in environments where durability is paramount.

For those concerned about security, Multi-Tech Systems has integrated multiple security features within these modems. This includes support for encryption protocols, ensuring that data transmitted over the modem remains secure and protected from unauthorized access.

In conclusion, the MT9234ZBA and MT9234ZBA-V by Multi-Tech Systems represent an excellent choice for anyone in need of reliable and high-speed modem solutions. With their advanced features, compatibility with various operating systems, and emphasis on security, these modems stand out in the crowded telecommunications market. Whether for home use or in a professional setting, the MT9234ZBA and MT9234ZBA-V offer robust solutions for modern communication needs.
Top Page Image Contents