Milan Technology CCSF30XX-100 specifications Technical Specifications, Troubleshooting

CCSCF30xx-10x

Cable Specifications -- Continued

CCSCF3039-100	1300 nm multimode
Fiber-optic Transmitter Power:	min: -19.0 dBm	max: -14.0 dBm
Fiber-optic Receiver Sensitivity:	min: -30.0 dBm	max: -14.0 dBm
Link Budget:	11.0 dB

The fiber optic transmitters on this device meet Class I Laser safety requirements per IEC-825/CDRH standards and comply with 21 CFR1040.10 and 21CFR1040.11.

Technical Specifications

For use with Transition Networks Model CCSCF30xx-10x or equivalent

Standards	FCC Class A; EN 55022 Class A; EN 55024; ANSI
	T1.102-1993; ETSI TBR-24; ITU-T G.703 G.823 for
	jitter tolerance; G.775 for loss of signal; Telecordia
	GR-499CORE & GR-253-CORE
Data Rate	DS3 / T3 = 44.7 Mb/s
	E3 = 34.4 Mb/s
Dimensions	3.4" x 5" x 0.87" (86 mm x 182 mm x 22 mm)
Weight	3 oz. (91 g) (approximately)
Power Consumption	6.0 Watts
MTBF	478,000 (MIL217F2 V5.0) (MIL-HDBD-217F)
	1,333,000 (Bellcore7 V5.0)
Environment	Tmra*:	0 to 60°C (32° to 140°F )
	Storage Temp:	-20° to 85°C (-4° to 185°F)
	Humidity:	5 to 95%, non condensing
	Altitude:	0 to 10,000 feet
Warranty	Lifetime

*Manufacturer’s rated ambient temperature: Tmra range for this slide-in-module depends on the physical characteristics and the installation configuration of the Transition Networks PointSystem™ chassis in which this slide-in-module will be installed.

The information in this user’s guide is subject to change. For the most up-to-date information on the CCSCF30xx-10x media converter, view the user’s guide on- line at: www.transition.com.

Product is certified by the manufacturer to comply with DHHS Rule 21/CFR, Subchapter J applicable at the date of manufacture.

CAUTION: Visible and invisible laser radiation when open. Do not stare into the beam or view directly with optical instruments.

CAUTION: Use of controls, adjustments or the performance of procedures other than those specified herein may result in hazardous radiation exposure.

Troubleshooting

If the media converter fails, isolate and correct the failure by determining the answers to the following questions and then taking the indicated action:

1.Is the PWR (Power) LED illuminated?

NO

•Ensure the media converter slide-in-module is installed properly in the chassis.

•Ensure the power cord is properly installed in the chassis and at the external power source.

•Ensure the external power source provides power.

•Contact Tech Support: 1-800-260-1312, Int’l: 00-1-952-941-7600.

YES

•Proceed to step 2.

2.Is the SDC (Signal Detect / Coax) LED illuminated green?

NO

•Check the coax cables for the proper connection.

•Contact Tech Support: 1-800-260-1312, Int’l: 00-1-952-941-7600.

YES

•Proceed to step 3.

3.Is the SDF (Signal Detect / Fiber) LED illuminated green?

NO

•Check the fiber cables for proper connection.

•Verify that the TX and RX cables on the local media converter are connected to the RX and TX ports, respectively, on the remote media converter.

•Contact Tech Support: 1-800-260-1312, Int’l: 00-1-952-941-7600.

YES

•Proceed to step 4.

4.Is the SDC (Signal Detect / Coax) LED flashing green?

YES

•The coax link is in loop-back mode. For normal operation, set the loop-back switch to the center (normal) position.

•Contact Tech Support: 1-800-260-1312, Int’l: 00-1-952-941-7600.

NO

•Proceed to step 5.

5.Is the SDF (Signal Detect / Fiber) LED flashing green?

YES

•The fiber link is in loop-back mode. For normal operation, set the loop-back switch to the center (normal) position.

•Contact Tech Support: 1-800-260-1312, Int’l: 00-1-952-941-7600.

NO

•Proceed to step 6.

8 24-hour Technical Support: 1-800-260-1312-- International: 00-1-952-941-7600 techsupport@transition.com -- Click the “Transition Now” link for a live Web chat. 9