Milan Technology CCSF30XX-100 specifications Set the Loop-Back Switch, Install the Slide-In-Module

CCSCF30xx-10x

Installation -- Continued

Set the Loop-Back Switch

The loop-back switch is located on the front panel of the media converter and is used for installation and network debugging procedures.

To set the switch, use a small flat-blade screwdriver or a			CL	FL
similar device (see the drawing to the right).
CL	(Coax loop-back)	Enable loop-back on the local coax interface.
--	(Center Position)	Normal operation.
FL	(Fiber loop-back)	Enable loop-back on the local fiber interface.

NOTE: Three loop-back test scenarios are described in detail on page 10.

Install the Slide-In-Module

CAUTION: Wear a grounding device and observe electrostatic discharge precautions when installing the CCSCF30xx-10x slide-in-module media converter. Failure to observe this caution could result in damage to, and subsequent failure of, the media converter.

To install the CCSCF30xx-10x media converter slide-in-module into the Transition Networks PointSystem™ chassis:

1.Locate an empty slot on the chassis.

2.Carefully slide the slide-in-module into the installation slot, aligning the module with the installation guides.

3.Ensure that the module is firmly seated inside the chassis.

4.Push in and rotate the attached panel fastener screw clockwise to secure the module to the chassis front.

		TX PWR			PWR		PWR	PWR
				LKS	LKS	LA		LKS	SPD	PWR
							LNK
				LKM	LKM	RXF		LKM	FRX	FLNK
		RX	LNK			RXC	COL		CRX	CLNK
		R		TX	TX		Link Alert	TX
		E				E	D
		S		Singlemode	Singlemode			Singlemode	TX
		E
I 0	I 0	T							100BASE-FX
		10BASE-T	INIT			10BASE
			TERM
				RX	RX	-		RX
						FL		TX	RX
				TX	TX
		SERIAL		Multimode	Multimode	0	50½	Multimode	100BASE-TX
						10BASE
				RX	RX			RX
						-2
		CPSMM120			CFMFF100	CETCF100		CFMFF100	CFETF100

Panel Fastener Screw

Installation -- Continued

Install the Coax Cable

1.Locate or build coax cables with female connectors installed at both ends.

2.Connect the coax cables to the media converter as described:

•Connect the female TX cable connector to the male TX port.

•Connect the female RX cable connector to the male RX port.

3.Connect the coax cables to the other device (switch, workstation, etc.) as described:

•Connect the female TX cable connector to the male RX port.

•Connect the female RX cable connector to the male TX port.

RX				RX
TX			TX
	Connect the coax cable	Connect the coax cable
	to the media converter	to the other device
	as shown.	(switch, work
		station, etc.) as shown

Install the Fiber Cable

1.Locate or build fiber cables with male, two-stranded TX to RX connectors installed at both ends.

2.Connect the fiber cables to the local CCSCF30xx-10x media converter as described:

•Connect the male TX cable connector to the female TX port.

•Connect the male RX cable connector to the female RX port.

3.Connect the fiber cables to the remote CCSCF30xx-10x media converter as described:

•Connect the male TX cable connector to the female RX port.

•Connect the male RX cable connector to the female TX port.

CCSCF

Connect the fiber cable to the local media converter as shown.

RX

TX

Connect the fiber cable to the remote media converter as shown

RX

TX

4 24-hour Technical Support: 1-800-260-1312-- International: 00-1-952-941-7600 techsupport@transition.com -- Click the “Transition Now” link for a live Web chat. 5