Lucent Technologies Host-Based Controller Modem AT Long Space Disconnect, Recall Stored Profile

Page 13

n = 0, 1

Otherwise

Data Addendum		Host-Based Controller Modem
June 15, 1998		AT Command Set

AT Command Reference (continued)
Yn	Long Space Disconnect
Long space disconnect is always disabled.
	Y0:	Disable long space disconnect (default).
	Y1:	Enable long space disconnect (NOT SUPPORTED).
Result Codes:
	OK	n = 0
	ERROR	Otherwise
Zn	Recall Stored Profile

This command instructs the modem chip set to go on-hook and restore the profile saved by the last &W command. Either Z0 or Z1 restores the same single profile.

Result Codes:

OK ERROR

&Bn	V.32 Auto Retrain
This modem always auto retrains.
	&B0:	Disable V.32 auto retrain (NOT SUPPORTED).
	&B1:	Enable V.32 auto retrain (default).
Result Codes:
	OK		n = 1
	ERROR		Otherwise
&Cn	Data Carrier Detect (DCD) Control

Data Carrier Detect is a signal from the modem to your computer indicating that the carrier signal is being received from a remote modem. DCD normally turns off when the modem no longer detects the carrier signal.

&C0: The state of the carrier from the remote modem is ignored. DCD circuit is always on.

&C1: DCD turns on when the remote modem's carrier signal is detected, and off when the carrier signal is not detected (default).

Result Codes:

OKn = 0, 1

ERROR Otherwise

Version 1.0

Lucent Technologies Inc.

13

Image 13

Contents

Introduction ContentsAT Command Set Summary Description AT Command SummaryS-Register Summary Default Description AT Testing and Debugging Command Set Summary Description#UD Result Code Summary NoEC-No error control protocol AT Commands Reference Online Data Character Echo Command Echo CommandDnDial Request ID Information Otherwise Hook ControlMars Lapm Monitor Speaker Mode Monitor Speaker VolumeModulation Handshake Select Pulse Dialing Return On-line to Data ModeResult Code Control VnDCE Response FormatResult Code Selection and Call Progress Monitoring Result Code OptionExt. Result Code Dial Tone Detect Busy Tone Detect Extended Result CodesLong Space Disconnect OK ErrorRecall Stored Profile Auto RetrainDn DTR Control Fn Load Factory SettingsGn V.22bis Guard Tone Control Auxiliary Relay optionQn Asynchronous Communications Mode Asynchronous Communications ModeLocal Flow Control Selection Pulse Dial Make-to-Break Ratio SelectionConnect Error Self-Test CommandsData Set Ready DSR Option SSE View Active Configuration and Stored ProfileYnSelect Stored Profile for Hard Reset Store Current ConfigurationZn=x Store Telephone Number \An\Nn Error Control Mode Selection Bits/s Rate Adjusted\Kn Break Control \N3 \Vn Protocol Result Code \Tn Inactivity Timer\Xn XON/XOFF Pass Through Data Calling ToneView Numbers in Blacklist Cn Data Compression Control En Enable/Disable Auto-Retrain and Fallback/Fall ForwardTest and Debug AT Commands AT#UD Last Call Status Report Format DiagGstnModulationSchemeActive from 3.7.2/V.58 Call Setup Result CodesCompressionActive from 3.2.2/V.58 Value Description ErrorControl Active from 3.5.2/V.58 Value DescriptionCallCleared codes from 3.6.4/V.58-1994 Value Description ImplementedDteHangupCommand S3Command Line Termination Character user defined AT Commands Reference S-RegistersAuto Answer Ring Number AT Escape Character user definedResponse Formatting Character user defined Command Line Editing Character user definedConnection Completion Time-Out S10 Comma Dial Modifier TimeS11 S12 Escape Guard TimeS21 24/General Bit Mapped Options Status S24 Timer to Control Sleep ModeS22 Results Bit Mapped Options Status S28S32 Synthetic Ring Volume S30 Inactivity TimerS33 Synthetic Ring Frequency S35S38 K56flex Downstream Rate S42 Auto Rate default 1, range 0 ¾1S48 Lapm Error Control and Feature Negotiation default S43 Auto Mode default 1, range 0¾1S48 S48 = S89AT FAX Command Set Summary AT FAX Command Set Class 1 FAXCommand Description AT FAX Commands Reference +FTM=m Transmit FAX Data with m Carrier Command Option Modulation Speed bits/s+FRM=m Receive FAX Data with m Carrier +FRH=m Receive Hdlc Data with m Carrier +FTH=m Transmit Hdlc Data with m CarrierFPR Manufacturer Identification +FMI +FAA Adaptive answerResult Lucent Data/Fax Product Identification +FMMAT Voice Command Set AT Voice Command SetVoice Commands AT Voice Command Set Not Defined In IS-101 SpecificationAT Voice Commands Reference AT+VGR=gain AT+VIT = Timer DTE/DCE Inactivity TimerAT+VEM=mask Event Reporting and Masking AT+VNH = Hook Automatic Hang-up ControlAT+VTD=dur AT+VLS=label Analog Source/Destination SelectionAT+VTS=string Start voice transmission and reception processAT+VSM? AT+VSD=sds, sdi Silence Detection Quiet and SilenceAT+VSM=? AT+VRN=interval Ringback Never Appeared Timer AT+VRA=interval Ringback Goes Away TimerAT+VPR=rate Select DTE/DCE Interface Rate Events Reported to the DTEAT+VTS= ATD DLE HAT+VLS=5 AT+VLS=7ATH Example # 2 Initiating a stored number speakerphone call Ring Example # 3 Answering a speakerphone callAT+FCLASS=1 ATAAT+FCLASS=0 Example # 6 Switching from speakerphone mode to TAD modeConnect AT+VLS=1DLE-R Modem answers call AT Dsvd Commands 25ter AT Commands 25ter AT CommandsManufacturer Identification +GMI? Version / Revision Information +GMR?V8o, v8a, and v8cf +ES? AT Commands+ES=? +ESA=? Idle,,,crctype,nrzien+ITF= off, on +ITF=?AT Commands for Homologation Testing and Debugging Version USA Country Codes CountryCode in HEXAT%T21,par#,paramvalue Pulse dial make time 255 ATD , ATX ATA, ATDATB ATH1Par # Parameter Description Range Reference Homologation ParametersVersion 150 255 100 120 255 0x00 0x12 0x10 0x88 0x80 0x06 0x0c 0x6b 0xaa Par. # Australia Belgium Denmark Finland France Germany 120 100 255 0x10 0x12 Norway Spain Par. # Netherlands Italy150 100 250 255 0x12 0x10 0x00 0x88 0x06 0x0c 0x80 Par. # Austria Japan China Korea Malaysia Singapore 150 250 255 Portugal Hong Kong 150 255 Version Par. # Canada Mexico India Vietnam Philippines 000 004 002 050 140 S10 020 S11 095 090 S30 S35 001 000 003 002 004 035 050 S10 020 S11 095 090 S30 S35 001 ATZ OK ATZ OK ATS11? 085 OKXX-XXXDMOD