Lucent Technologies Host-Based Controller Modem AT specifications Ata, Atd, Atd , Atx, Atb, ATH1

Page 66

Host-Based Controller Modem	Data Addendum
AT Command Set	June 15, 1998

AT Commands for Homologation Testing and Debugging (continued)

Table 13. The Homologation Parameters (continued)

Par #	Parameter Description		Range	Reference

19	Number of failed attempts allowed before	0—255		ATD
	blacklisting
1a	Troubled call delay in minutes	0—255		ATD
1b	Ineffective call delay in minutes	0—255		ATD
1c	Erroneous call delay in minutes	0—255		ATD
1d	Blacklisting duration in multiple of 10 minutes	0—255;		ATD
		0	= only delayed and no blacklisting
		255 = no limit (i.e., till power turned off)
1e	Over-current sense validation time in	0—255, 0 = current sense disabled.		ATA, ATD
	multiples of 10 ms
1f	Calling tone flag	0	= disabled	ATD , S35
		1	= enabled, and disable with ^ dial
			modifier permitted
		2	= enabled, and disable with ^ dial
			modifier not permitted
20	Blind dial flag	0	= not permitted	ATD , ATX
		1	= permitted
		2	= permitted with speaker on
21	Busy detect disable (with ATX) flag	0	= not permitted	ATD , ATX
		1	= permitted
22	Guard tone type	0	= not present & adjustable	S37
		1	= 550 Hz, 2 = 1800 Hz
23	Bell modes permitted flag	0	= not permitted	ATB
		1	= permitted
24	Off-hook (ATH1) restrictions	0	= no restrictions	ATH1
		1	= restricted by S7 duration
		2	= not allowed
25	Shunt relay on time during off-hook in	0—255		ATD
	multiples of 10 ms.	0	= shunt relay disabled
26	Hook flash time in multiples of 10 ms	0—255		ATD
		0	= hook flash not allowed
27	Min. blind dial pause in seconds	0—65		S6
28	Max. blind dial pause in seconds	0—65		S6
29	Min. no answer time-out in seconds	0—65		S7
2a	Max. no answer time-out in seconds	0—65		S7
2b	Min. dial pause time in seconds	0—65		S8
2c	Max. dial pause time in seconds	0—65		S8
2d	Min. no carrier disconnect time in multiples of	1—65		S10
	100 ms
2e	Max. no carrier disconnect time in multiples of	1—255		S10
	100 ms
2f	Transmit level in dB with implied minus sign	0—255		ATD
30	Dial modifier validation	0 = if an invalid dial modifier is found, treat the		—
		entire dial string as null (no digits dialed)
		1 = ignore invalid dial modifiers

66

Lucent Technologies Inc.

Version 1.0

Image 66

Contents

Contents IntroductionAT Command Summary AT Command Set Summary DescriptionAT Testing and Debugging Command Set Summary Description S-Register Summary Default Description#UD Result Code Summary NoEC-No error control protocol AT Commands Reference Echo Command Online Data Character Echo CommandDnDial Otherwise Hook Control Request ID InformationMars Lapm Monitor Speaker Volume Monitor Speaker ModeModulation Handshake Result Code Control Return On-line to Data ModeSelect Pulse Dialing VnDCE Response FormatExt. Result Code Dial Tone Detect Busy Tone Detect Result Code OptionResult Code Selection and Call Progress Monitoring Extended Result CodesRecall Stored Profile OK ErrorLong Space Disconnect Auto RetrainGn V.22bis Guard Tone Control Fn Load Factory SettingsDn DTR Control Auxiliary Relay optionLocal Flow Control Selection Asynchronous Communications ModeQn Asynchronous Communications Mode Pulse Dial Make-to-Break Ratio SelectionSelf-Test Commands Connect ErrorData Set Ready DSR Option View Active Configuration and Stored Profile SSEZn=x Store Telephone Number Store Current ConfigurationYnSelect Stored Profile for Hard Reset \AnBits/s Rate Adjusted \Nn Error Control Mode Selection\Kn Break Control \N3 \Xn XON/XOFF Pass Through \Tn Inactivity Timer\Vn Protocol Result Code Data Calling ToneView Numbers in Blacklist En Enable/Disable Auto-Retrain and Fallback/Fall Forward Cn Data Compression ControlTest and Debug AT Commands Diag AT#UD Last Call Status Report FormatCall Setup Result Codes GstnModulationSchemeActive from 3.7.2/V.58CallCleared codes from 3.6.4/V.58-1994 ErrorControl Active from 3.5.2/V.58 Value DescriptionCompressionActive from 3.2.2/V.58 Value Description Value Description ImplementedDteHangupCommand Auto Answer Ring Number AT Commands Reference S-RegistersS3Command Line Termination Character user defined AT Escape Character user definedCommand Line Editing Character user defined Response Formatting Character user definedConnection Completion Time-Out S11 Comma Dial Modifier TimeS10 S12 Escape Guard TimeS22 Results Bit Mapped Options Status S24 Timer to Control Sleep ModeS21 24/General Bit Mapped Options Status S28S33 Synthetic Ring Frequency S30 Inactivity TimerS32 Synthetic Ring Volume S35S42 Auto Rate default 1, range 0 ¾1 S38 K56flex Downstream RateS48 S48 = S43 Auto Mode default 1, range 0¾1S48 Lapm Error Control and Feature Negotiation default S89AT FAX Command Set Class 1 FAX AT FAX Command Set SummaryCommand Description AT FAX Commands Reference Command Option Modulation Speed bits/s +FTM=m Transmit FAX Data with m Carrier+FRM=m Receive FAX Data with m Carrier +FTH=m Transmit Hdlc Data with m Carrier +FRH=m Receive Hdlc Data with m CarrierFPR Result Lucent Data/Fax +FAA Adaptive answerManufacturer Identification +FMI Product Identification +FMMVoice Commands AT Voice Command SetAT Voice Command Set AT Voice Command Set Not Defined In IS-101 SpecificationAT Voice Commands Reference AT+VEM=mask Event Reporting and Masking AT+VIT = Timer DTE/DCE Inactivity TimerAT+VGR=gain AT+VNH = Hook Automatic Hang-up ControlAT+VTS=string AT+VLS=label Analog Source/Destination SelectionAT+VTD=dur Start voice transmission and reception processAT+VSD=sds, sdi Silence Detection Quiet and Silence AT+VSM?AT+VSM=? AT+VPR=rate Select DTE/DCE Interface Rate AT+VRA=interval Ringback Goes Away TimerAT+VRN=interval Ringback Never Appeared Timer Events Reported to the DTEAT+VTS= DLE H ATDAT+VLS=7 AT+VLS=5ATH Example # 2 Initiating a stored number speakerphone call AT+FCLASS=1 Example # 3 Answering a speakerphone callRing ATAConnect Example # 6 Switching from speakerphone mode to TAD modeAT+FCLASS=0 AT+VLS=1DLE-R Modem answers call AT Dsvd Commands Manufacturer Identification +GMI? 25ter AT Commands25ter AT Commands Version / Revision Information +GMR?V8o, v8a, and v8cf AT Commands +ES?+ES=? +ITF= off, on Idle,,,crctype,nrzien+ESA=? +ITF=?AT Commands for Homologation Testing and Debugging Version Country Codes CountryCode in HEX USAAT%T21,par#,paramvalue Pulse dial make time 255 ATB ATA, ATDATD , ATX ATH1Homologation Parameters Par # Parameter Description Range ReferenceVersion 150 255 100 120 255 0x00 0x12 0x10 0x88 0x80 0x06 0x0c 0x6b 0xaa Par. # Australia Belgium Denmark Finland France Germany 120 100 255 0x10 0x12 Par. # Netherlands Italy Norway Spain150 100 250 255 0x12 0x10 0x00 0x88 0x06 0x0c 0x80 Par. # Austria Japan China Korea Malaysia Singapore 150 250 255 Portugal Hong Kong 150 255 Version Par. # Canada Mexico India Vietnam Philippines 000 004 002 050 140 S10 020 S11 095 090 S30 S35 001 000 003 002 004 035 050 S10 020 S11 095 090 S30 S35 001 OK ATZ OK ATS11? 085 OK ATZXX-XXXDMOD