Liebert S3 Options user manual 7KHýIROORZLQJýFKDUDFWHUVýDUHýYDOLGýIRUýDýWHOHSKRQHýQXPEHUã

çï ,IýDýVHFRQGýGLDOðRXWýQXPEHUýLVýGHVLUHGñýSUHVVýWKHýULJKWýDUURZýWRýGLVSOD\ýWKHý3KRQHý1XPEHUýëý VFUHHQýDQGýUHSHDWý6WHS èýWRýHQWHUýDýVHFRQGýWHOHSKRQHýQXPEHUýIRUýDQRWKHUýUHPRWHýFRPSXWHUýRUý DýSDJHU

7KHýIROORZLQJýFKDUDFWHUVýDUHýYDOLGýIRUýDýWHOHSKRQHýQXPEHUã

Table 16 Telephone Number Characters

Remote Modem and/or Pager Characters

CharacterDescription

0 - 9 Are the actual digits of the telephone number.

!Force the modem to perform a “hook flash” (i.e., hang up quickly and release) operation. The hook-flash is sometimes used in office phone systems to signal the local switchboard to listen for special codes to follow.

-Make the telephone number more readable. They are ignored by the modem, and can be ( ) <SPACE> placed anywhere in the field.

,Forces the modem to pause 2 seconds before continuing to dial. A comma should be used when you must dial “9” to get an outside line. If the modem must pause for a bit after dialing 9 for an outside line, the complete dial string may looking like this: 9, 555-8243.

WCauses the modem to wait before continuing. W means “wait for a dial tone.”

RStands for “Reverse.” The R command is a prefix which tells the modem to connect with an originate-only modem. Without the prefix, the UPStation S3 modem may not communicate with an originate-only modem. If used, R must be prefixed to any digits dialed, i.e., R 9, 555- 8325.

T, P	Selects tone or pulse dialing. Only one of these can be used in a given number. They are both
	prefixes, the T stands for tone (i.e., touch tone) and the P stands for pulse. By default, the
	modem uses tone dialing. If the UPS is connected to a phone line which requires pulse dialing,
	a P must be prefixed to the number, i.e., P 555-8325.

@Is used to wait past a recorded voice message that is requesting additional information input such as a recording giving instructions for entering an extension or password. When used, @ commands the modem to wait 5 seconds before continuing to the next part of the dial string.

;Forces the modem to return to command mode after dialing. Unless you are very familiar with modems, we recommend that you not use this command.

Pager-Only Characters

Character Description

#Signifies the end of the number. Most pager service equipment require that the pound symbol be used to terminate an entry.

*Generates a separator character between fields in the display window. For example, if the pager display string is 555*8325, it appears in the pager window as 555-8325.

?Holds the event ID code (pager only) before being transmitted to the pager service equipment. (See the Dial-out Events in Table 15 for the list of ID codes and associated events.) For example, if the modem is dialing a pager because of a battery test failed, the ? character is replaced with the number “1” before transmission. The number 1 then appears in the pager display window at the same location in which it appeared in the pager display number field.

46 Internal Modem