Zenith XBS344 warranty Connections, Connecting Antenna/Cable TV to DVD/VCR Receiver

Page 11

Connections

ips

Depending on your TV and other equipment you wish to connect, there are various ways you could connect the DVD/VCR Receiver. Use connections described on pages 11-14.

Please refer to the manuals of your TV, VCR, Stereo System or other devices as necessary to make the best connections.

Caution

Make sure the DVD/VCR Receiver is connected directly to the TV. Tune the TV to the correct video input channel.

Do not connect the DVD/VCR Receiver’s DVD/VCR AUDIO OUT jack to the phono in jack (record deck) of your audio system.

Do not connect your DVD/VCR Receiver via your VCR. The DVD image could be distorted by the copy protection sys- tem.

Connecting Antenna/Cable TV to DVD/VCR Receiver

1

Disconnect the antenna leads from the rear of the

TV.

2 Identify the type of cable from your antenna. If it is a round cable as illustrated, it is a 75 ohm coaxial antenna cable. This cable will connect directly to the jack marked ANT.IN on your DVD/VCR Receiver.

ip

If your antenna lead wire is a flat type antenna cable, connect it to an Antenna Adapter (300-ohm to 75-ohm) (not supplied) and slip the adapter onto the ANT.IN jack. The adapter does not screw on to the DVD/VCR Receiver, it just slips over the jack.

Antenna Antenna

Cable TV

Wall Jack

Flat Wire

 

 

(300 ohm)

 

 

300/75 ohm

OR

OR

Adapter

 

 

(Not supplied)

 

 

DVD+VCR Connections Panel

Without Cable Box

If your cable wire is connected to your TV without a converter or descrambler box, unscrew the wire from your TV and attach it to the ANT.IN jack on the DVD/VCR Receiver. Use the sup- plied round coaxial cable to connect between the DVD/VCR Receiver’s RF.OUT jack and the 75 ohm antenna input jack on the TV. With this connection, you can receive all midband, super band, and hyperband channels (all cable channels).

With Cable Box

If a converter is required in your cable system, follow the instruction below:

The cable hookup permits both TV and DVD/VCR Receiver operation.

To view or record a CATV channel

1Tune the TV to the DVD/VCR Receiver output channel (CH 3 or 4).

2Set the DVD/VCR Receiver channel selector to the output channel of the Cable Converter box using CH/TRK (v/V) or number (0-9) of your DVD/VCR Receiver. (Example: CH3)

3Select the channel to view at the Cable Converter Box.

otes

With this connection, you CANNOT record one program while viewing another.

If you are using a cable box to tune channels, it is not nec- essary to do Auto Channel Programming, (Auto Channel Search) as indicated on page 18.

Cable TV

Wall Jack

Back Panel of

Typical Cable Box

DVD+VCR Connections Panel

PREPARATION

11

Image 11
Contents Installation and Operating Guide Warranty Regulatory Information FCC Part Safety PrecautionsImportant Safety Instructions Table of Contents Playable Discs Remote Control Operating RangeRemote Control Battery Installation Before UseSelecting the Viewing Source PrecautionsAbout Symbols Eject PowerVolume Front PanelDisplay Window Overview Indicates sound mode isRemote Control Overview Digital Audio in Optical Rear Panel Connections OverviewVideo OUT DVD OUT Connections Connecting Antenna/Cable TV to DVD/VCR ReceiverOptional TV Connections Connections Basic TV ConnectionsAbout Ferrite Core Connections Speaker System ConnectionsSpeaker Positioning Game Device Digital Set Top Box Rear of DVD/VCR Receiver Accessory Audio/Video A/V Connections to DVD/VCR ReceiverConnections Radio Antenna Connections Digital Device ConnectionsFM/AM Selecting Input/Output SourcesDVD VCRWhile DVD is inserted Sound ModeVolume Control MutingMenu Selection VCR Operation Setup On-Screen Display OSDOn-Screen Menus Setup Channel Selection VCR Operation Setup VCR Setup Menu OptionsManual Clock Set VCR Operation Setup Setting the ClockAuto Clock Set On-screen display operation DVD Operation Setup DVD Operational OverviewPlayback Status Indicator Icons On-Screen DisplayLanguage DVD Operation Setup Initial SettingsPicture Basic Menu OperationOthers DRC/Vocal/AutoPlay DVD Operation SetupSpeaker setup Rating DVD Special Effect Playbacks VCR Operation Normal PlaybackTo record one TV program while watching another Timer RecordingVCR Operation Basic Recording To pause recordingProgram Priority Checking Erasing Timer Record ProgrammingVCR Operation Dubbing and Editing Instant Timer RecordingChecking the Recording Time To extend the Recording TimeMTS Multi-Channel TV Sound Multichannel TV Sound Indicator MTSVHS Hi-Fi Stereo System MTS Broadcast Playback with Hi-Fi Stereo Audio SoundAdditional Information VCR Operation Tape Counter Memory FeatureDVD Operation Playing DVDs General FeaturesDVD Operation General Features Special DVD Features Audio CD and MP3 Disc Operation Search CD MP3 Pause CD MP3Selecting Tracks CD MP3 Repeat Track/All/Off CD MP3To flip the picture Jpeg File Operation Viewing Jpeg Files on a Disc JpegSelecting other Files Still PictureErasing Track from the Program List Programmed Playback CD MP3Programmed Playback with Audio CDs or MP3 Discs Repeat Programmed TracksSpeaker Setup Repeat steps 2 to 5 to store other stations Radio OperationListening to the Radio To Clear Stored Radio StationsPress 2 to move to the station name column Symptom Cause Solution TroubleshootingReference Moisture Condensation Symptom Cause CorrectionCode Language Language Code ListCode Country Country Code ListSpecifications Speakers FM TunerAM Tuner Reference Customer INTER-ACTIVE Center Numbers Warranty Period HOW Service is HandledThis Limited Warranty does not Apply to Issue O