GarrettCom P62-Series manual Technical Specifications Ports Performance, Network Standards

Page 6

Magnum P62-Series Hardened Switches

Installation and User Guide (08/03)

Rev A 04/01: This revision is the initial release of the P62F Hardened Switches user manual.

1.0SPECIFICATIONS

1.1Technical Specifications

Ports Performance

Fiber, and when an auto-negotiating port is operating at 100Mbps: Data Rate: 100Mbps

When an RJ-45 auto-negotiating port is operating at 10 Mbps: Data Rate: 10 Mbps

For mP62 models, RJ-45 ports are S/W controlled for speed and F/H duplex, crossover (MDI – MDIX) is automatically handled

Network Standards

100Mb: Ethernet IEEE 802.3u, 100BASE-TX, 100BASE-FX

10 Mb: Ethernet IEEE 802.3, 10BASE-T

Auto-sensing for speed: IEEE 802.3u; 802.3x flow control

For managed mP62 models, IEEE 802.1p QoS and 802.1d Spanning Tree For mP62 management software, see Section 2.2.3

Packet-Processing Between Domains is non-blocking

Filtering and Forwarding Rate from 100Mbps ports: 148,800 pps max

Filtering and Forwarding Rate from 10 Mbps ports: 14,880 pps max.

Processing type: Store and Forward

Auto-learning: 4K address table (16K on P62F), shared for all ports

Packet buffers: 256KB, dynamically shared on all domains

Latency (not including packet time): 100 to 10 Mbps: 5s 10 to 100Mbps: 5s

Path Delay Value: 50 BT on all ports

Maximum Ethernet Segment (or Domain) Lengths

10BASE-T (Unshielded twisted pair)

- 100 m (328 ft)

100BASE-TX (CAT 5 UTP)

- 100 m (328 ft)

100BASE-FX, full-duplex: (multi-mode)

- 2.0 km (6,562 ft)

100BASE-FX, full-duplex: (single-mode)

- 20.0 km (65,620 ft)

100BASE-FX, full-duplex: (single-mode, long)

- 40.0 km (131,240 ft)

Operating Environment

Ambient Temperature: -40°F to 170°F for mP62 (160°F for P62F) (-40°C to 75°C for mP62, 70°C for P62F))

Cold start down to -20°C

Storage Temperature: -40° to 185°F (-40°C to 85°C)

Ambient Relative Humidity: 5% to 95% (non-condensing)

Altitude: -200 to 50,00 ft. (-60 to 15,000m)

“Plenum rated” for above-the-ceiling installation in office areas IEC 529 rated IP51 (holds out dust, vertical water)

Operating Shock and Vibration: Meets Bellcore GR-63-CORE

www . GarrettCom . com

2

Image 6
Contents Installation and User Guide Hardened Ethernet Switches Installation and User Guide TrademarksGarrettCom, Inc Contacting GarrettCom, IncPersonal Switches, 10/100Mb Stackable Hubs, Snmp OptionalPersonal Hubs, 10Mb series Appendix a Warranty Information Network Standards SpecificationsTechnical Specifications Ports Performance Maximum Ethernet Segment or Domain LengthsFiber Ports # 1 Power Supply Internal 24VDC and -48VDC Power SupplyLED Indicators MechanicalMtbf Bellcore method Agency Approvals Ordering Information PartsManaged P62-Series mP62 Hardened Switches Introduction Inspecting the Package and ProductProduct Description Www . GarrettCom . com Www . GarrettCom . com Managed Network Software MNS-mP for Magnum mP62 Connecting the Console Terminal to Magnum mP62 Management Console portFiber port, SC Connectors Frame Buffering and LatencyWww . GarrettCom . com 24VDC and -48VDC Int. & 125V/250VDC ext. through PSX-T Two future-proof fiber ports with SC connectorsTop-mounted LEDs for convenient viewing Managed mP62’s with MNSmP software for Managed networkApplications Example Example 3. Magnum mP62 Mounting dimensions InstallationLocating Magnum P62F-Series 10/100Mb Ethernet Switches Mounting position and materialsMounting Hole Dimensions, inches & cm Connecting Ethernet Media, and Special Strain-relief feature Media Ieee StandardConnecting Fiber Optic SC-type, Snap-In Connecting Fiber Optic ST-type, Snap-In OptionalConnecting Single-Mode Fiber Optic Power Budget Calculations for P62-Series Fiber Media TypicalDC Power Terminals +, -,internally floating P62 -48V, 24VDC InstallationWiring Pin out P62F-5V Power Adaptor Power the P62-5V models w/Ext AC Power Supply PSX-AAC Power Connector IEC-type UL RequirementsPower the P62-5V w/DC Pwr Supply PSX-T at 125/250 VDC Power Output 5VDC, 3AmpsOperating Shock Cable Strain Relief Feature on all P62-Series models DIN-Rail mounting option for mP62 Series Switching, Address Learning Dual-Speed Functionality, and SwitchingSwitching, Filtering and Forwarding OperationLED’s for P62-Series Hardened Switch Auto-negotiation and Speed-sensingTroubleshooting Before Calling for AssistanceWhen Calling for Assistance Return Material Authorization RMA ProcedureAppendix a Warranty Information No Problem FoundShipping and Packaging Information