GarrettCom 6K32TRC user manual Www . GarrettCom . com

Page 64

Magnum 6K32T & 6K32TRC Managed Switch

Installation and User Guide 05/07)

ports for cascaded connection. This feature eliminates the need for a special twisted pair crossover cable when connecting to a hub or another switch.

Each port has an Activity (ACT) LED indicating packets being received, a Link (LK) LED that indicates proper connectivity with the remote device when lit, a FDX/HDX LED to indicate full-duplex mode when lit (or half-duplex when off), and a “10/100” LED indicating 100Mb when lit (or 10 Mbps when off).

Important Note: The 10/100 RJ-45 ports are supported with Auto-negotiation and Auto-crossover (MDIX), which allow the RJ-45 ports to automatically Link with any RJ- 45 device and eliminate the use of cross-over cable.

The RJ-45 pins normally (TP crossover switch) are per the standard for hubs-to- users twisted pair wiring: 1 = receive+, 2 = receive-, 3 = transmit+, 6 = transmit-, other pins not used. When the TP crossover push-button is UP, the pins of the RJ- 45 port are per the standard for up-links using twisted pair wiring, i.e., the transmit and the receive pairs are exchanged: 1 = transmit+, 2 = transmit-, 3 = receive+, 6 = receive-, other pins not used.

NOTE: for Power Substations: In support of the IEEE 1613 Class 2 standard, GCI

advises that, for substation applications, the RJ-45 ports are intended for connectivity to other communication equipment such as routers or telecommunication multiplexers installed in close proximity (i.e., less than 2 meters or 6.5ft) to the 6K32. It is not recommended to use these ports in substation applications to interface to field devices across distances which could produce kigh (greater than 2500V ) levels of ground potential rise (GPR) during line-to-ground fault conditions. The 6K32 passes the 1613specifications for zero packet loss with fiber ports & with RJ45 ports used as indicated here.

5.2.10a. New PoE (Power Pass-through), model P6KP8V-RJ45 (MDIX), 10/100Mb 8-port

The PoE RJ-45 ports act similar to regular RJ-45 ports, except they have capability of providing power on each port to power up the PD devices, per the IEEE802.3af PoE standard. The Power Pass-through PoE modules are totally dependent upon the powerful -48VDC input power supply to support more RJ-45 (10/100) ports. Each port requires at least 15watts to power up the PoE PD devices. In this Fig. the top 8- RJ45 ports are enhanced with POE option The 8-RJ45 POE modules are also available with mix –n-match with fiber modules. Please check the ordering information Sec.1.2 for all the various P6K PoE modules option.

www . GarrettCom . com

59

Image 64
Contents Managed Switch 6K32TTrademarks Contacting GarrettCom, Inc Canadian EmissionSpecifications 6K32T & 6K32TRC Managed Switch Port Modules Magnum Line Technical Specifications PerformanceNetwork Standards and Compliance Maximum 10 Mbps Ethernet Segment LengthsFiber connector types supported Management Console connectorPower Supply Internal Maximum Standard Gigabit Ethernet Segment LengthsRelay Alarm Contact Optional Cooling MethodConfiguration Options Ordering InformationMagnum 6K32T & 6K32TRC Port Modules 6KP8-45MT 6KP8-45MLC 6KP8-45SLC 6KP6-MT10ST 6KP6-RJ10STGigabit Options Modules using Gbic Modules with Gb, not using GBICs6K32T/6K32TRC PoE Modules with 48VDC Pass-Through Www . GarrettCom . com Introduction Inspecting the Package and Product Product Description Magnum 6K32TRC Managed Switch Www . GarrettCom . com 1a Magnum 6K32T Managed Switch Chassis Eight-port SFF fiber modules 6K8-MTRJ, 6K8-MLC, 100Mb fiber Eight-Port Copper Module, 6K8-RJ45 MdixSpeed when OFF when auto Negotiation is not disabled @RJ-45 + 2@ 100Mb ST or SC Four-Port 10 Mb mm Fiber ST Modules Copper and 2@10Mb fiber mm ST Ports.@ RJ-45 + 2@ 10 Mb ST Operation of the SFF fiberGigabit 1000Mbps port modules Packet Prioritization, 802.1p QOS Frame Buffering and Flow ControlManaged Network Software MNS-6K for Magnum 6K32T & 6K32TRC MIBs for Snmp visit„ Managed switching for high performance Ethernet LANs Features and Benefits„ Features Fiber-Built-In Example 1 Magnum 6K32T Switch for a Vlan application ApplicationsData Example 3 Redundant Application 6K32TRC 6K32TRC in a Redundant application 6K32TRC with IGMP-L2 mode Installation Locating Magnum 6K32T SwitchesConnecting Ethernet Media Connecting Fiber Optic ST-type, twist-lockIeee Standard Media Type Max. Distance Port Module Fiber CopperConnecting Single-Mode Fiber Optic Connecting Fiber Optic SC-type, Snap-InMedia Ieee Standard Gigabit SFP Small Form-factor Pluggable Optical Transceivers Side View Duplex LC connector Front view Bail claspSFP-SX SFP-LX10 SFP-LX25 SFP-ZX40 SFP-ZX70 6KP4 ’cvrRack-mounting for 19 Retma racks, Magnum 6K32T & 6K32TRC’s Table-Top or Shelf Mounting1 Dual Side-Mountings for Magnum 6K32T & 6K32TRC units Rack-mounting, Reverse version of the Magnum 6K32T’s Powering the Magnum 6K32T & 6K32TRC Managed Switch 6K32T & 6K32TRC Port Module 6KPM Installation Preparation for Installing and Removing 6KPMsRemove Chassis Cover 1a Removing front panel after the screws being removed1b Pulling out the top coved from the chassis base Installing 6KPM Cards in the Magnum 6K32T & 6K32TRC 1d Top View 6KPM retaining screws hold Face PlateWww . GarrettCom . com Www . GarrettCom . com Removing 6KPM Cards Retaining screws shown by arrows . Remove 6KPM CardConsole DB-9 Port Rear View of Magnum 6K32TDB-9 Console port connector Pin Signal Description1 RS-232 DB-9 Console Com port Serial port pin assignments Filtering and Forwarding Switching FunctionalityAddress Learning Status LEDs Auto-Cross MDIXAuto-negotiation, for 10/100Mbps RJ-45 portsWww . GarrettCom . com Magnum 6K32T & 6K32TRC Managed Switch Port Modules Flow-control, Ieee 802.3x standard6KPM Module Description Lock Combo Module1b 6KP4-F10ST, 4@10Mb multi-mode FX-ST twist lock Module Transceivers all in one module. This Mode 100Mbps fiber opticActivity ACT, Link LK, Mode SC-type connectors. It Equipped with 4 dual speedCopper ports and 2 Single Provides an advantage Through combining copper5 6KP8-MTRJ, 8 @100Mb multi-mode FX , Mtrj Small-Form-factor Port@ 100Mbps Multi-Mode Fiber portWww . GarrettCom . com 7 6KP8-MLC, 8 ports @ 100Mbps multi-mode LC connector Small 9 6KP8-RJ45 Twisted Pair 10/100Mb 8-PortWww . GarrettCom . com PoE LEDs Summary 48VDC power in not No power is coming toInternally connected PoE ports for some Reason, all the PoE port LEDs are onGBIC-SXSC Gigabit fiber1000Mb, multi-mode SC Connector Small size of LC connectorsGive an advantage of placing more Ports on one module. The 6KP8-4512a GBPM-2OTX Two Gigabit option 13 6KM-BLNK 12b GBIC-LXSC Gigabit fiber 1000Mb, multi-mode SC Connector@ 1000Mb Fiber SC + 2@ 100Mb SC Before Calling for Assistance When Calling for Assistance Return Material Authorization RMA ProcedureNo Problem Found Shipping and Packaging InformationAppendix B Internal DC Power Supply Options Power Supply Internal -48VDC OptionB3.0 Applications for DC Powered Switches B4.1 UL Requirements for DC-powered units 6K32TRC -48VDCInstallation and User Guide 05/07 C3.0 DUAL-SOURCE OPTION, Theory of Operation C5.1 UL Requirements Example Magnum 6K32T & 6K32TRC-48VDC

6K32T, 6K32TRC specifications

The GarrettCom 6K32TRC and 6K32T are advanced, ruggedized network switches designed for mission-critical applications in challenging environments. These switches are notable for their reliability, versatility, and high performance, making them ideal for industries such as transportation, utilities, and industrial automation.

One of the key features of the 6K32TRC and 6K32T is their robust construction. These switches are built to withstand extreme temperatures, humidity, and harsh conditions, ensuring continued operation even in the most demanding settings. With an operational temperature range of -40°C to +75°C, they can function effectively in various climates, making them perfect for outdoor or unconditioned environments.

Both models are equipped with Layer 2 and Layer 3 switching capabilities, offering flexibility for different networking needs. The 6K32T, for instance, is designed specifically for applications that require high-speed connectivity and data management. With support for various Ethernet protocols, these switches provide reliable data transmission and low latency, essential for real-time applications.

The 6K32TRC model features enhanced redundancy and failover capabilities. It supports a range of network topologies including ring, star, and mesh configurations, ensuring that network uptime is maximized even in the face of component failures. Redundant power supply options further guarantee continuous operation.

Scalability is another highlight of the GarrettCom 6K32 series. The switches are modular, allowing users to easily add or replace various interface cards to support additional network connections or management features without significant downtime.

Security is paramount in industrial settings, and the 6K32TRC and 6K32T adhere to modern cybersecurity standards. They include features such as access control lists (ACLs), Secure Shell (SSH) for encrypted management access, and VLAN tagging to enhance network security.

In terms of management, the switches support an array of protocols for easy integration and monitoring within existing networks. SNMP, RMON, and web-based management interfaces streamline the administrative process, ensuring that network managers can efficiently oversee their operations.

Overall, the GarrettCom 6K32TRC and 6K32T switches exemplify reliability and advanced technology. Their robust design, comprehensive feature set, and focus on security make them an excellent choice for organizations requiring resilient network solutions in challenging industrial environments.