GE GFK-2193A user manual IC693PBS201 Slave Module Specifications, Key

Page 6

1

4

SYS

COM

PROFIBUS DP

SLAVE

SERVICE RS232

5-IGND

3-TxD

2-RxD

PROFIBUS

5-IGND

8-A

3-B

1-SHLD

IC693PBS201

PROFIBUS

Slave Module

1

2

3

	Key

	1	LEDs	System (SYS) and Communications (COM)
	1	LEDs	indicators
			indicators
	2	Service Port	RS232, 9-pin male, D-Shell Connector. Used
	2	Service Port	for module firmware upgrades.
			for module firmware upgrades.
	3	PROFIBUS	9-pin female D-Shell Connector. Used for
	3	Port	connecting to a PROFIBUS network.
		Port	connecting to a PROFIBUS network.
	4	Label (not	Label on side of module contains catalog
		Label (not	number, description, standard conformance,
		shown)	number, description, standard conformance,
		shown)	and serial number information
			and serial number information

Figure 1-1. PROFIBUS Slave Module

IC693PBS201 Slave Module Specifications

Catalog number	IC693PBS201
Description	Series 90-30 Slave module for PROFIBUS DP networks
Configuration software	Requires Proficy Machine Edition Logic Developer version 2.6 or later
requirement
CPU version	Requires CPU firmware version 8.00 or later
requirement
Mounting location	Can reside in any Series 90-30 baseplate (CPU, expansion, or remote)
	slot except for slot 1 of a modular CPU baseplate
Environment	Storage temperature = –40°C to 85°C
	Operating temperature = 0°C to 60°C

Backplane current	450 mA at 5VDC (typical)
consumption
Data rates	Supports all standard Data Rates (9.6KBps, 19.2KBps, 93.75KBps,
	187.5KBps, 500KBps, 1.5Mbps, 3MBps, 6MBps and 12MBps)
Status information	Slave Status Word
	Firmware module revision

Note: The PROFIBUS Slave module does not support Sync and Freeze modes

1-2

Series 90™-30 PROFIBUS Slave Module User's Manual – August 2004

GFK-2121A

Image 6

Contents GE Fanuc Automation Programmable Control ProductsAs Used in this Publication Cimstar Contents Contents Overview and Specifications Profibus InformationRelated Publications IC693PBS201 Slave Module Specifications KeyProfibus Basics Profibus Network OverviewBus Communication Network Topology Amount of Data Transmission Duration FrequencyNetwork Connectors Pin No Signal DesignationInstallation Reviewing System Power RequirementsInstalling the Profibus Module in the PLC Rack Connecting the Slave to the Profibus Network Network Segment LengthBaud Rate Line a Line B Glass Fiber Distance Max 1 Profibus Cable Types Network TerminationNetwork Baud Rate Removing the Module from the RackConfiguration Adding a Profibus Slave Module to the Hardware ConfigurationConfiguring a Profibus Slave Module Settings TabInput Data Area Tab Profibus Slave Module’s Input Data Area ParametersPower Consumption Tab Output Data Area TabStatus and Diagnostics Profibus Slave Module LED IndicatorsColor Indication Network Parameter Errors Status/Firmware ID ArrayWord 1 Slave Status Word Sysid Examples Communication RequestsCommreq Ladder Instruction Slot Word ValueOperation of the Communications Request PLCError Detection and Handling Corrective Actions for Commreq ErrorsCommreq Programming Requirements and Recommendations Commreq Status Word Value DescriptionGet Slave Status Commreq Get Slave Status Command Block Basic ExampleProfibus Slave Module Commreq Reference Memory TypesGet Slave Status Reply Data Format Bit Meaning ValueNetwork Parameter Errors Read Module Header Command Block Basic Example Read Module HeaderValue Type Dec Hex Description Read Module Header Reply Data Format for Slave Clear Counters Command Block Basic Example Clear CountersClear Counters Reply Data Format Index