GE GFK-2193A user manual Get Slave Status Reply Data Format, Bit Meaning Value

Page 25

4

(Word 7) Command Code: Word 7 specifies the Command code for the COMMREQ to be executed. Get Slave Status = 3.

(Word 8) Local PLC - Memory Type: Words 8—9 specify the location in the PLC where the response will be written. Valid values for Word 8 are listed on page 4-7.

(Word 9) Local PLC - Memory Starting Address: Word 9 determines the starting address in the local PLC in which the response is to be written. The value entered is the offset (0-based) from the beginning of PLC memory for the memory type and mode specified in Word 8. This offset will be either in bits, bytes, or words depending on the mode specified (for example, if Word 8=16 and Word 9=2, the starting address will be %I9). Valid ranges of values depend on the PLC’s memory ranges.

(Word 10) Response Memory Size: Words 10 specifies the size of the memory block for the response. (Must be at least 2 words.)

Get Slave Status - Reply Data Format

Word

Name

Description

 

 

 

Word 1

Command Code

Echo of Command code that this data block is replying

 

 

to. (0x0003)

Word 2

Status Code

See Word 2 formats in table below

Word 3—10

Reserved for Future

Word 10 of the command block should specify a

 

Use

minimum of 5 words to accommodate possible future

 

 

use of this space.

Note: The reply from Get Slave Status contains the same information that is provided to the PLC CPU in the Status/Firmware ID Address. This parameter is defined when the module is configured in the PLC hardware configuration.

Word 2 – Status Code

Bit

Meaning

Value

 

 

 

15—12

Baud Rate (bps)

0=12MBps, 1=6MBps, 2=3MBps, 3=1.5MBps,

 

 

4=500KBps, 5=187.5KBps, 6=93.75Bps, 8=19.2KBps,

 

 

9=9.6KBps

11—10

Module State

0=Module is waiting for parameters from Master

 

 

1=Module is waiting for config from Master

 

 

2=Data Exchange is occurring – normal operation

 

 

3=Error (either config error or module watchdog

 

 

timeout)

9

On-line

1=Online module firmware is running

 

 

0=Offline

8

PLC Cfg

0= Module config from PLC CPU is bad

 

 

1=Module config from PLC CPU is good

7

Run/Stop

0=Stop, 1=Run This is the State of the PROFIBUS

 

 

Module, it is not the status of the PLC CPU. If the SYS

 

 

LED is Green the bit=1, if the SYS LED is Red or

 

 

Amber the bit=0

6—0

Error Info

See “Network Parameter Errors”

4-8

Series 90™-30 PROFIBUS Slave Module User's Manual – August 2004

GFK-2193A

Page 24 Page 26
Image 25
Page 24 Page 26
Contents Programmable Control Products GE Fanuc AutomationCimstar As Used in this PublicationContents Contents Profibus Information Overview and SpecificationsRelated Publications Key IC693PBS201 Slave Module SpecificationsProfibus Network Overview Profibus BasicsBus Communication Amount of Data Transmission Duration Frequency Network TopologyPin No Signal Designation Network ConnectorsReviewing System Power Requirements InstallationInstalling the Profibus Module in the PLC Rack Network Segment Length Connecting the Slave to the Profibus NetworkBaud Rate Line a Line B Glass Fiber Distance Max 1 Network Termination Profibus Cable TypesRemoving the Module from the Rack Network Baud RateAdding a Profibus Slave Module to the Hardware Configuration ConfigurationSettings Tab Configuring a Profibus Slave ModuleProfibus Slave Module’s Input Data Area Parameters Input Data Area TabOutput Data Area Tab Power Consumption TabProfibus Slave Module LED Indicators Status and DiagnosticsColor Indication Status/Firmware ID Array Network Parameter ErrorsWord 1 Slave Status Word Commreq Ladder Instruction Communication RequestsSysid Examples Slot Word ValuePLC Operation of the Communications Request Corrective Actions for Commreq Errors Error Detection and Handling Commreq Programming Requirements and Recommendations Value Description Commreq Status WordProfibus Slave Module Commreq Reference Get Slave Status Command Block Basic ExampleGet Slave Status Commreq Memory TypesBit Meaning Value Get Slave Status Reply Data FormatNetwork Parameter Errors Read Module Header Read Module Header Command Block Basic ExampleValue Type Dec Hex Description Read Module Header Reply Data Format for Slave Clear Counters Clear Counters Command Block Basic ExampleClear Counters Reply Data Format Index
Top Page Image Contents