GE 1601-9026-A3 quick start RJ45 Connectors Metres max length

Page 23

QUICKSTART GUIDE

For the second twisted wire pair one wire is White with orange bands while the other wire is orange.

The third twisted wire pair #3 consists of a white wire with green bands and a second wire that is green.

The final wire pair, wire pair #4 consists of a white wire with brown bands while the other wire is Brown.

*The Electronic Industry Association (EIA) / Telecommunications Industry Association's (TIA) Standard 568B

The pin and wire configuration of a patch or crossover cable used to connect or establish a point-to-point Ethernet LAN between two Ethernet devices is shown here.

RJ45 Connectors

100 metres max length

FIGURE 12: Pin Layout for RJ45 Ethernet Crossover (Patch) Cable

MULTILINK ETHERNET COMMUNICATIONS SWITCH – QUICKSTART GUIDE

19

Image 23
Contents Quickstart Guide MultilinPage Table of Contents Tagged Vlans & Ring only Mode Determining Mounting Location PrecautionsPreparation Quickstart Guide Rack Mounting ML2400 Mechanical InstallationTable-top or Shelf Mounting Unit with DIN-rail clips DIN-Rail / Panel Mounting ML1600DIN-rail latch detail Unit mounting dimensions Mounting Dimensions with Metal BracketsDIN-Rail / Panel Mounting ML1200/ML800 Mounting Dimensions for ML1200/ML800 with metal bracketsQuickstart Guide Powering the Unit ML2400 Electrical InstallationPowering the Unit ML1200/ML800 Powering the Unit ML1600Alarm Contacts UL Requirements for DC-Powered UnitsFigure below is a typical example of the set-up Dielectric Strength hi-pot Testing1 ML2400/ML1600 Connecting a Management Console Terminal to the UnitDescription 2 ML1200/ML800 Pinout information for above connectorTwisted Pair copper cable Introduction to Twisted Pair and Fiber Optic Ethernet LANsEthernet Physical Layer Twisted Pair Copper vs Fiber Optic Mesh Architecture Supported Network Topologies Fiber Star ArchitectureUnshielded Twisted Pair cable 10BASE T and 100BaseT MediaRing Architecture Metres max Ethernet Unshielded Twisted PairRJ45 Connectors Metres max length Connecting ST-type Fiber Optics twist-lock Connecting Ethernet MediaConnecting RJ45 Twisted Pair Connecting SC-type Fiber Optics snap-inConnecting Single-mode Fiber Optics Connecting Gigabit Media using GBICs Wavelengths of light Hubs and SwitchesFiber Optic Ethernet Single and Multi-mode cable Fiber Cable Cross Section and Physical SpecificationsDifferences between Multi-Mode and Single-Mode Cable Single mode fiber Less attenuation per unit distanceOptical Power Budget Common Fiber Optic Connectors Assigning an IP address to the Multilin SwitchQuickstart Guide Quickstart Guide Quickstart Guide Quickstart Guide Quickstart Guide Assigning a static IP Address to a personnel computer Quickstart Guide Quickstart Guide Quickstart Guide Quickstart Guide Quickstart Guide Configuring the switch ports for UR redundant operation Quickstart Guide Relay has switched over to the alternate port Background Tagged VLANs & Ring Only ModeConfiguring Tagged VLANs Configuring a Vlan within the switch Save Quickstart Guide Quickstart Guide Configure You have now completed the exercise Configuring the Multilink switch for Ring Only Mode Quickstart Guide Select Bridge Rstp Then Save Enable Status Once saved, select OK, then OK again to exit Quickstart Guide Then Save Enable status Disable LLA On Ports That are in a Ring Selecting the Proper Version Multilink Firmware UpdatesUpgrading Using a Serial Connection- Command Line Interface Updating MultiLink FirmwareQuickstart Guide Following procedure describes how to upgrade the firmware ML800/1200/1600/2400# show version This completes the upgrade process Using FTP Updating Using the EnerVista Web Interface SoftwareUsing Tftp Quickstart Guide Reboot the switch when the transfer is complete Quickstart Guide