Fortinet FortiGate-5001FA2 manual Contents

Page 3

Contents

Contents
Warnings and cautions	2
FortiGate-5001FA2 security system	5
Front panel LEDs and connectors	6
LEDs	6
Connectors	7
Accelerated packet forwarding and policy enforcement	7
FA2 interfaces and active-active HA performance	8
Base backplane gigabit communication	8
Hardware installation	9
RAM DIMMs	9
Installing SFP transceivers	10
Changing FortiGate-5001FA2 jumper settings	11
Inserting a FortiGate-5001FA2 board into a chassis	13
Before inserting the FortiGate-5001FA2 board in a chassis	14
Insertion procedure	14
Removing a FortiGate-5001FA2 board from a chassis	17
Troubleshooting	18
FortiGate-5001FA2 does not startup	18
FortiGate-5001FA2 cannot display chassis information	20
Quick Configuration Guide	21
Registering your Fortinet product	21
Planning the configuration	21
NAT/Route mode	22
Transparent mode	22
Choosing the configuration tool	23
Web-based manager	23
Command Line Interface (CLI)	23
Factory default settings	24
Configuring NAT/Route mode	24
Using the web-based manager to configure NAT/Route mode	25
Using the CLI to configure NAT/Route mode	26
Configuring Transparent mode	27
Using the web-based manager to configure Transparent mode	27
Using the CLI to configure Transparent mode	28
Upgrading FortiGate-5001FA2 firmware	28
FortiGate-5001FA2 base backplane data communication	30
Powering off the FortiGate-5001FA2 board	31

FortiGate-5001FA2 Security System Guide
01-30000-0379-20080606	3

Image 3

Contents C u r i t y S y s t e m G u i d e Page Contents For more information FortiGate-5001FA2 security system LEDs Front panel LEDs and connectorsAccelerated packet forwarding and policy enforcement ConnectorsFA2 interfaces and active-active HA performance Base backplane gigabit communicationRAM DIMMs To install FortiGate-5001FA2 RAM DIMMsLocation of FortiGate-5001FA2 RAM Dimm slots Installing SFP transceiversTo install SFP transceivers Changing FortiGate-5001FA2 jumper settingsFortiGate-5001FA2 jumper settings Inserting a FortiGate-5001FA2 board into a chassis To change or verify the JP3 jumper settingOpen Insertion procedureBefore inserting the FortiGate-5001FA2 board in a chassis ClosedHandle Unlock FortiGate-5001FA2 normal operating LEDs Removing a FortiGate-5001FA2 board from a chassis Troubleshooting All chassis left handle not contacting power switchFortiGate-5001FA2 does not startup Location of FortiGate-5001FA2 power switch FortiGate-5001FA2 cannot display chassis information All chassis Firmware problemRegistering your Fortinet product Planning the configurationTransparent mode NAT/Route modeChoosing the configuration tool Command Line Interface CLIWeb-based manager Configuring NAT/Route mode Factory default settingsUsing the web-based manager to configure NAT/Route mode To configure interfaces Go to System Network InterfaceTo configure the Default Gateway Config system interface edit port2 Using the CLI to configure NAT/Route modeConfiguring Transparent mode Using the web-based manager to configure Transparent modeTo switch from NAT/Route mode to transparent mode Go to System Status Using the CLI to configure Transparent modeTo upgrade the firmware using the web-based manager Upgrading FortiGate-5001FA2 firmwareTo upgrade the firmware using the CLI Under System Information Firmware Version, select UpdateFortiGate-5001FA2 base backplane data communication To power off a FortiGate-5001FA2 board Powering off the FortiGate-5001FA2 boardPowering off the FortiGate-5001FA2 board Customer service and technical support Fortinet documentationRegister your Fortinet product Regulatory compliance Trademarks