Fortinet FortiGate-5001FA2 manual Factory default settings, Configuring NAT/Route mode

Page 24

Factory default settings

Quick Configuration Guide

Factory default settings

The FortiGate-5001FA2 unit ships with a factory default configuration. The default configuration allows you to connect to and use the FortiGate-5001FA2 web-based manager to configure the FortiGate-5001FA2 board onto the network. To configure the FortiGate-5001FA2 board onto the network you add an administrator password, change the network interface IP addresses, add DNS server IP addresses, and, if required, configure basic routing.

Table 5: FortiGate-5001FA2 factory default settings

Operation Mode

NAT/Route

 

 

Administrator Account

User Name: admin

 

Password: (none)

 

 

port1 IP/Netmask

192.168.1.99/24

 

 

port2 IP/Netmask

192.168.100.99/24

 

 

Default route

Gateway: 192.168.100.1

 

Device: port2

 

 

Primary DNS Server:

65.39.139.53

 

 

Secondary DNS Server:

65.39.139.53

 

 

Note: At any time during the configuration process, if you run into problems, you can reset the FortiGate-5001FA2 board to the factory defaults and start over. From the web-based manager go to System > Status find System Operation at the bottom of the page and select Reset to Factory Default. From the CLI enter execute factory reset.

Configuring NAT/Route mode

Use Table 6 to gather the information you need to customize NAT/Route mode settings for the FortiGate-5001FA2 security system. You can use one table for each board to configure.

Table 6: FortiGate-5001FA2 board NAT/Route mode settings

Admin Administrator Password:

port1

IP:

_____._____._____._____

Netmask:

_____._____._____._____

 

port2

IP:

_____._____._____._____

Netmask:

_____._____._____._____

 

 

Device (Name of the Interface

 

 

connected to the external

 

 

network):

 

 

Default Gateway IP address:

 

Default Route

_____._____._____._____

 

The default route consists of the

name of the interface connected

 

to an external network (usually the Internet) and the default

 

gateway IP address. The default route directs all non-local traffic to

 

this interface and to the external network.

 

 

 

DNS Servers

Primary DNS Server:

_____._____._____._____

Secondary DNS Server:

_____._____._____._____

 

 

FortiGate-5001FA2 Security System Guide

24

01-30000-0379-20080606

Image 24
Contents C u r i t y S y s t e m G u i d e Page Contents For more information FortiGate-5001FA2 security system Front panel LEDs and connectors LEDsConnectors Accelerated packet forwarding and policy enforcementBase backplane gigabit communication FA2 interfaces and active-active HA performanceTo install FortiGate-5001FA2 RAM DIMMs RAM DIMMsInstalling SFP transceivers Location of FortiGate-5001FA2 RAM Dimm slotsChanging FortiGate-5001FA2 jumper settings To install SFP transceiversFortiGate-5001FA2 jumper settings To change or verify the JP3 jumper setting Inserting a FortiGate-5001FA2 board into a chassisInsertion procedure Before inserting the FortiGate-5001FA2 board in a chassisClosed OpenHandle Unlock FortiGate-5001FA2 normal operating LEDs Removing a FortiGate-5001FA2 board from a chassis Troubleshooting All chassis left handle not contacting power switchFortiGate-5001FA2 does not startup Location of FortiGate-5001FA2 power switch All chassis Firmware problem FortiGate-5001FA2 cannot display chassis informationPlanning the configuration Registering your Fortinet productNAT/Route mode Transparent modeChoosing the configuration tool Command Line Interface CLIWeb-based manager Factory default settings Configuring NAT/Route modeUsing the web-based manager to configure NAT/Route mode To configure interfaces Go to System Network InterfaceTo configure the Default Gateway Using the CLI to configure NAT/Route mode Config system interface edit port2Configuring Transparent mode Using the web-based manager to configure Transparent modeTo switch from NAT/Route mode to transparent mode Using the CLI to configure Transparent mode To upgrade the firmware using the web-based managerUpgrading FortiGate-5001FA2 firmware Go to System StatusUnder System Information Firmware Version, select Update To upgrade the firmware using the CLIFortiGate-5001FA2 base backplane data communication Powering off the FortiGate-5001FA2 board To power off a FortiGate-5001FA2 boardPowering off the FortiGate-5001FA2 board Customer service and technical support Fortinet documentationRegister your Fortinet product Trademarks Regulatory compliance