Fortinet MR8 manual Using the setup wizard, To start the setup wizard

Page 43

Transparent mode installation

Using the setup wizard

 

 

Example

If the default gateway IP is 204.23.1.2 and this gateway is connected to port 2:

config router static edit 1

set dst 0.0.0.0 0.0.0.0 set gateway 204.23.1.2 set device port2

end

Using the setup wizard

From the web-based manager, you can use the setup wizard to begin the initial configuration of the FortiGate unit. For information about connecting to the web-based manager, see “Connecting to the web-based manager” on page 16.

The first time you connect to the FortiGate unit, it is configured to run in NAT/Route mode.

To switch to Transparent mode using the web-based manager

1Go to System > Status.

2Select Change beside the Operation Mode.

3Select Transparent in the Operation Mode list.

4Select OK.

To reconnect to the web-based manager, change the IP address of the management computer to 10.10.10.2. Connect to the internal or DMZ interface and browse to https:// followed by the Transparent mode management IP address. The default FortiGate Transparent mode management IP address is 10.10.10.1.

To start the setup wizard

1Select Easy Setup Wizard (the middle button in the upper-right corner of the web-based manager).

2Use the information that you gathered in Table 9 on page 40 to fill in the wizard fields. Select the Next button to step through the wizard pages.

3Confirm your configuration settings, and then select Finish and Close.

Reconnecting to the web-based manager

If you changed the IP address of the management interface while you were using the setup wizard, you must reconnect to the web-based manager using the new IP address. Browse to https:// followed by the new IP address of the management interface. Otherwise, you can reconnect to the web-based manager by browsing to https://10.10.10.1. If you connect to the management interface through a router, make sure that you have added a default gateway for that router to the management IP default gateway field.

FortiGate-60 Installation Guide

01-28008-0018-20050128

43

Image 43
Contents January 01-28008-0018-20050128 Installation GuideRegulatory Compliance TrademarksTable of Contents Index Introduction Secure installation, configuration, and managementWeb-based manager Command line interfaceDocument conventions Setup wizardFortiGate documentation FortiGate Installation GuideFortiManager documentation Related documentationFortinet Knowledge Center Comments on Fortinet technical documentationFortiMail documentation Customer service and technical supportFortiLog documentation Customer service and technical support Customer service and technical support Getting started Mounting Package contentsTo power on the FortiGate unit Turning the FortiGate unit power on and offPower requirements Environmental specificationsTo connect to the web-based manager Connecting to the web-based managerStop bits Flow control Connecting to the command line interface CLITo connect to the CLI Bits per second 9600 Data bits ParityGo to System Network DNS Quick installation using factory defaultsFactory default Dhcp server configuration Factory default FortiGate configuration settingsFactory default NAT/Route mode network configuration Management IP Factory default Transparent mode network configurationFactory default firewall configuration Administrative accessStrict Factory default protection profilesScan NAT/Route mode Planning the FortiGate configurationExample NAT/Route mode network configuration NAT/Route mode with multiple external network connectionsExample NAT/Route multiple internet connection configuration Transparent modeWeb-based manager and setup wizard Configuration optionsNext steps Preparing to configure the FortiGate unit in NAT/Route mode NAT/Route mode installationDhcp or PPPoE configuration Using the web-based managerPPPoE settings User name Password To add a default route Configuring basic settingsTo configure interfaces Go to System Network Interface To configure DNS server settings Go to System Network DNSTo configure interfaces Using the command line interfaceConfiguring the FortiGate unit to operate in NAT/Route mode To add/change the administrator passwordGet system interface ExampleTo configure DNS server settings Using the setup wizardInternal servers Setup wizard settings PasswordExternal Interface Dhcp serverStarting the setup wizard Connecting the FortiGate unit to the networksSetup wizard settings Antivirus FortiGate-60 FortiGate-60 NAT/Route mode connectionsConfiguring the Modem interface Configuring the networksTo register the FortiGate unit Go to System Config TimeTo configure virus, attack, and spam definition updates To set the date and timeGo to System Maintenance Update Center Preparing to configure Transparent mode Transparent mode installationManagement IP To change the Management IP Go to System Network ManagementTo change to Transparent mode using the CLI Reconnecting to the web-based managerTo configure the default gateway To configure the management IP addressTo start the setup wizard Internal Connecting the FortiGate unit to your networkTo register your FortiGate unit Go to System Maintenance Update Center Priorities of heartbeat device and monitor priorities High availability installationConfiguring FortiGate units for HA operation High availability configuration settingsGroup ID MAC Address To change the FortiGate unit host name Config system global Set hostname namestr end Configuring FortiGate units for HA using the CLITo configure the FortiGate unit for HA operation Connecting the cluster to your networksTo connect the cluster HA network configurationInstalling and configuring the cluster Installing and configuring the cluster Selecting a modem mode Configuring the modem interfaceRedundant mode configuration To operate in standalone mode Go to System Network Modem Standalone mode configurationRedundant for Configuring modem settingsMode Auto-dialTo configure modem settings Go to System Network Modem Connecting and disconnecting the modem in Standalone modeTo connect to a dialup account Go to System Network Modem ISP Defining a Ping ServerDead gateway detection To disconnect the modemAdding firewall policies for modem connections CLI IndexIndex