Fortinet 5001A-DW manual Resetting a FortiGate-5001A board, Installing and removing AMC modules

Page 20

Resetting a FortiGate-5001A board

Hardware installation

Resetting a FortiGate-5001A board

You must eject the FortiGate-5001A board from the chassis slot to cycle the power and reset the board. See “Removing a FortiGate-5001A board” on page 18 for information about how to eject a FortiGate-5001A board from a chassis.

Installing and removing AMC modules

!

!

This section describes installing a FortiGate AMC Double width Module (ADM) in the FortiGate-5001A-DW front panel AMC double-width opening or a FortiGate AMC Single width Module (ASM) in the FortiGate-5001A-SW front panel AMC single-width opening.

Caution: Do not operate the FortiGate-5001A board with an open AMC opening. For optimum cooling performance and safety, the AMC opening must contain a slot filler panel or a FortiGate AMC module.

Caution: Because the FortiGate-5001A board does not support hot swapping AMC modules, you must eject the FortiGate-5001A board from its chassis slot and completely open the handles before inserting or removing AMC modules or slot filler panels.

Table 6: FortiGate AMC module LEDs

LED

State

Description

 

 

 

HS

Off

Normal operation.

 

 

 

 

Blue

Ejection latch open.

 

 

 

 

Flashing

The module is starting up or shutting down.

 

 

 

OOS

Off

LED currently not in use.

 

 

 

PWR

Amber

The module is properly inserted in the FortiGate unit.

 

 

 

 

Off

The module is not receiving power from the FortiGate unit.

 

 

 

OT

Off

LED currently not in use.

 

 

 

LINK

Green

The correct cable is in use and the connected equipment has

 

 

power.

 

Off

No link established.

 

 

 

ACT

Flashing

Network activity at this interface.

 

Green or

 

 

Amber

 

 

Off

No network activity at this interface.

 

 

 

ACT/RDY

Amber

The module is properly inserted in the FortiGate unit.

 

 

 

 

Off

The module is not receiving power from the FortiGate unit.

 

 

 

PORT

Off

LED currently not in use.

 

 

 

This section describes:

Inserting AMC slot filler panels

Inserting AMC modules

Removing AMC modules

 

FortiGate-5001A Security System Guide

20

01-30000-83456-20081023

Image 20
Contents FortiGate-5001A Page Contents For more information FortiGate-5001A security system Front panel LEDs and connectors Front panel LEDs and connectorsLEDs Lists and describes the FortiGate-5001A LEDsFabric backplane communication ConnectorsBase backplane communication AMC modules FortiGate-RTM-XB2FortiGate-ASM-FB4 Hardware installation Changing FortiGate-5001A SW11 switch settings SW11To change or verify the SW11 switch setting Location of SWFortiGate-5001A mounting components OpenInserting a FortiGate-5001A board To insert a FortiGate-5001A board into a chassis slotOpen the handles to their fully open positions FortiGate-5001A normal operating LEDs Removing a FortiGate-5001A board To remove a FortiGate-5001A board from a chassis slotRemoving a FortiGate-5001A board Resetting a FortiGate-5001A board Installing and removing AMC modulesTo install an AMC slot filler panel Inserting AMC slot filler panelsInserting AMC modules To insert an AMC module into a FortiGate-5001A boardRemoving AMC modules To remove an AMC module from a FortiGate-5001A boardFortiGate-5001A does not start up TroubleshootingAll chassis Firmware problem To remove and reset an AMC module FortiGate AMC modules not detected by FortiGate-5001A boardPlanning the configuration Registering your Fortinet productNAT/Route mode Transparent modeChoosing the configuration tool Web-based managerCommand Line Interface CLI Factory default settingsConfiguring NAT/Route mode Using the web-based manager to configure NAT/Route mode To configure interfaces Go to System Network InterfaceUsing the CLI to configure NAT/Route mode To configure the Default GatewayConfiguring Transparent mode Using the web-based manager to configure Transparent modeUsing the CLI to configure Transparent mode To switch from NAT/Route mode to transparent modeUpgrading FortiGate-5001A firmware To upgrade the firmware using the web-based managerTo upgrade the firmware using the CLI FortiGate-5001A base backplane data communication CLI FortiGate-5001A fabric backplane data communication Powering off the FortiGate-5001A board To power off a FortiGate-5001A boardPowering off the FortiGate-5001A board Register your Fortinet product Customer service and technical supportFortinet documentation Trademarks Regulatory compliance

5001A-SW, 5001A-DW specifications

Fortinet's FortiGate 5001A is a high-performance, next-generation firewall designed to meet the demands of large enterprises and data centers. The model comes in two distinct configurations—the 5001A-DW for data center workloads and the 5001A-SW for enhanced security capabilities.

The 5001A-DW is specifically tailored for critical data center environments, offering robust security and seamless integration into virtualized infrastructures. Its hardware design accommodates high capacity and throughput, beneficial for managing large volumes of data without compromising on security. This variant supports advanced networking technologies, such as Software-Defined Networking (SDN) and Network Function Virtualization (NFV), making it a versatile solution for organizations looking to optimize their network performance.

On the other hand, the 5001A-SW focuses more on advanced threat protection, integrating Fortinet’s FortiOS operating system, which provides comprehensive and consolidated security features. This model is engineered to safeguard against sophisticated cyber threats through its AI-powered security analytics and automated response capabilities. With an array of built-in security features, including IPS (Intrusion Prevention System), Application Control, and Web Filtering, the 5001A-SW enhances visibility and control over the network environment.

Both models provide exceptional SSL inspection capabilities, allowing organizations to analyze encrypted traffic without latency. With Fortinet's Security Fabric technology, the 5001A series offers integrated security across various network layers, streamlining security management and improving response times to threats.

The appliances also support advanced routing protocols and capabilities like Virtual Routing and Forwarding (VRF) to facilitate complex network designs. Their flexibility in deployment makes them suitable for a variety of environments, whether on-premises or in the cloud.

In terms of performance, the FortiGate 5001A series boasts impressive throughput rates, ensuring that organizations can scale their security measures in line with their growth. They are designed to minimize downtime, allowing for continuous and uninterrupted security operations.

Overall, the Fortinet FortiGate 5001A-DW and 5001A-SW models stand out for their scalability, advanced threat protection, and robust performance, positioning them as essential tools for organizations seeking to fortify their defenses against evolving cyber threats in today's digital landscape.