Fortinet 5001A-SW, 5001A-DW manual AMC modules, FortiGate-RTM-XB2

Page 9

 

 

FortiGate-5001A security system

AMC modules

FortiGate-RTM-XB2

The FortiGate-RTM-XB2 module provides two 10-gigabit fabric backplane interfaces and NP2 processor acceleration for FortiGate-5001A fabric interfaces. For 10-gigabit fabric backplane communications, each FortiGate-5001A board requires one FortiGate-RTM-XB2 module. The FortiGate-RTM-XB2 module is an ATCA rear transition module (RTM) that installs into an RTM slot at the back of a FortiGate-5140 and FortiGate-5050 chassis.

To support 10-gigabit fabric backplane communications your FortiGate-5140 or FortiGate-5050 chassis must also include one or more FortiSwitch-5003A boards or other 10-gigabit fabric backplane switching boards installed in the chassis in fabric slots 1 and 2.

Note: On some versions of the FortiGate-5001A firmware, when a FortiGate-5001A board starts up with a FortiGate-RTM-XB2 module installed, the fabric1 and fabric2 interfaces are replaced with interfaces that are named RTM/1 and RTM/2 to indicate the presence of the FortiGate-RTM-XB2module. Configuration settings that include the fabric1 and fabric2 interface names will have to be changed to use the RTM/1 and RTM/2 interface names.

Figure 3: FortiGate-RTM-XB2 front panel

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Retention

 

Power

Retention

Screw

 

LED

Screw

 

Handle

Handle

The FortiGate-RTM-XB2 NP2 processors provide hardware accelerated network processing for eligible traffic passing through the FortiGate-RTM-XB2 interfaces. For information about Fortinet NP2 processor acceleration, see the Fortinet Hardware Acceleration Technical Note.

Follow the instructions in the FortiGate-RTM-XB2 System Guide to install the FortiGate-RTM-XB2 module.

AMC modules

You can install one FortiGate AMC Double width Module (ADM) in the

FortiGate-5001A-DW front panel AMC double-width opening. For example:

The FortiGate-ADM-XB2, provides 2 NP2 accelerated XFP 10-gigabit interfaces.

The FortiGate-ADM-FB8, provides 8 NP2 accelerated SFP 1-gigabit interfaces.

Figure 4: FortiGate-ADM-XB2

HS

 

 

OOS

LINK

LINK

PWR

 

 

OT

ACT

ACT

 

 

1

2

ADM-XB2

 

 

You can install one FortiGate AMC Single width Module (ASM) in the

FortiGate-5001A-SW front panel AMC single-width opening. For example:

FortiGate-5001A Security System Guide

 

01-30000-83456-20081023

9

Image 9
Contents FortiGate-5001A Page Contents For more information FortiGate-5001A security system Front panel LEDs and connectors Front panel LEDs and connectorsLists and describes the FortiGate-5001A LEDs LEDsConnectors Base backplane communicationFabric backplane communication FortiGate-RTM-XB2 AMC modulesFortiGate-ASM-FB4 Hardware installation SW11 Changing FortiGate-5001A SW11 switch settingsLocation of SW To change or verify the SW11 switch settingOpen FortiGate-5001A mounting componentsTo insert a FortiGate-5001A board into a chassis slot Inserting a FortiGate-5001A boardOpen the handles to their fully open positions FortiGate-5001A normal operating LEDs To remove a FortiGate-5001A board from a chassis slot Removing a FortiGate-5001A boardRemoving a FortiGate-5001A board Installing and removing AMC modules Resetting a FortiGate-5001A boardInserting AMC slot filler panels To install an AMC slot filler panelInserting AMC modules To insert an AMC module into a FortiGate-5001A boardTo remove an AMC module from a FortiGate-5001A board Removing AMC modulesTroubleshooting All chassis Firmware problemFortiGate-5001A does not start up FortiGate AMC modules not detected by FortiGate-5001A board To remove and reset an AMC moduleRegistering your Fortinet product Planning the configurationTransparent mode NAT/Route modeWeb-based manager Choosing the configuration toolFactory default settings Configuring NAT/Route modeCommand Line Interface CLI To configure interfaces Go to System Network Interface Using the web-based manager to configure NAT/Route modeTo configure the Default Gateway Using the CLI to configure NAT/Route modeUsing the web-based manager to configure Transparent mode Configuring Transparent modeTo switch from NAT/Route mode to transparent mode Using the CLI to configure Transparent modeTo upgrade the firmware using the web-based manager To upgrade the firmware using the CLIUpgrading FortiGate-5001A firmware FortiGate-5001A base backplane data communication CLI FortiGate-5001A fabric backplane data communication To power off a FortiGate-5001A board Powering off the FortiGate-5001A boardPowering off the FortiGate-5001A board Customer service and technical support Fortinet documentationRegister your Fortinet product Regulatory compliance Trademarks

5001A-SW, 5001A-DW specifications

Fortinet's FortiGate 5001A is a high-performance, next-generation firewall designed to meet the demands of large enterprises and data centers. The model comes in two distinct configurations—the 5001A-DW for data center workloads and the 5001A-SW for enhanced security capabilities.

The 5001A-DW is specifically tailored for critical data center environments, offering robust security and seamless integration into virtualized infrastructures. Its hardware design accommodates high capacity and throughput, beneficial for managing large volumes of data without compromising on security. This variant supports advanced networking technologies, such as Software-Defined Networking (SDN) and Network Function Virtualization (NFV), making it a versatile solution for organizations looking to optimize their network performance.

On the other hand, the 5001A-SW focuses more on advanced threat protection, integrating Fortinet’s FortiOS operating system, which provides comprehensive and consolidated security features. This model is engineered to safeguard against sophisticated cyber threats through its AI-powered security analytics and automated response capabilities. With an array of built-in security features, including IPS (Intrusion Prevention System), Application Control, and Web Filtering, the 5001A-SW enhances visibility and control over the network environment.

Both models provide exceptional SSL inspection capabilities, allowing organizations to analyze encrypted traffic without latency. With Fortinet's Security Fabric technology, the 5001A series offers integrated security across various network layers, streamlining security management and improving response times to threats.

The appliances also support advanced routing protocols and capabilities like Virtual Routing and Forwarding (VRF) to facilitate complex network designs. Their flexibility in deployment makes them suitable for a variety of environments, whether on-premises or in the cloud.

In terms of performance, the FortiGate 5001A series boasts impressive throughput rates, ensuring that organizations can scale their security measures in line with their growth. They are designed to minimize downtime, allowing for continuous and uninterrupted security operations.

Overall, the Fortinet FortiGate 5001A-DW and 5001A-SW models stand out for their scalability, advanced threat protection, and robust performance, positioning them as essential tools for organizations seeking to fortify their defenses against evolving cyber threats in today's digital landscape.