Fortinet 5001A-SW, 5001A-DW manual Inserting AMC slot filler panels, Inserting AMC modules

Page 21

 

 

Hardware installation

Installing and removing AMC modules

Inserting AMC slot filler panels

!

!

!

The following procedure describes how to install a slot filler panel in the FortiGate-5001A front panel AMC opening. The FortiGate-5001A-DW board includes one AMC double-width slot filler panel and the FortiGate-5001A-SW board includes one AMC single-width slot filler panel.

Caution: Do not operate the FortiGate-5001A board with an open AMC opening. For optimum cooling performance and safety, the AMC opening must contain a slot filler panel or a FortiGate AMC module.

Caution: Because the FortiGate-5001A board does not support hot swapping AMC modules, you must eject the FortiGate-5001A board from its chassis slot and completely open the handles before inserting or removing AMC modules or slot filler panels.

To install an AMC slot filler panel

To complete this procedure, you need:

FortiGate-5001A board with an empty AMC slot

An electrostatic discharge (ESD) preventive wrist strap with connection cord

Caution: FortiGate-5001A boards must be protected from static discharge and physical shock. Only handle or work with FortiGate-5001A boards at a static-free workstation. Always wear a grounded electrostatic discharge (ESD) preventive wrist strap when handling FortiGate-5001A boards.

1Attach the ESD wrist strap to your wrist and to an available ESD socket or wrist strap terminal.

2Eject the FortiGate-5001A board from the chassis slot.

3With the FortiGate-5001A left (top) handle fully open, pull the latch on the slot filler front panel to the extended position.

4Insert the slot filler panel by applying moderate force to the front faceplate to slide the slot filler panel into the opening.

The slot filler panel should glide smoothly into the opening. If you encounter any resistance while sliding the slot filler panel in, the slot filler panel could be aligned incorrectly. Pull the slot filler panel back out and try inserting it again.

5Press the latch in the slot filler front panel to lock in the slot filler panel.

Inserting AMC modules

!

!

The following procedure describes how to install an AMC module into your FortiGate-5001A front panel AMC opening. Insert the fiber transceivers into the module before inserting the module into the FortiGate unit. For details on installing the transceivers, see the QuickStart Guide for the AMC module.

To insert an AMC module into a FortiGate-5001A board

Caution: Do not operate the FortiGate-5001A board with an open AMC opening. For optimum cooling performance and safety, the AMC opening must contain a slot filler panel or a FortiGate AMC module.

Caution: Because the FortiGate-5001A board does not support hot swapping AMC modules, you must eject the FortiGate-5001A board from its chassis slot and completely open the handles before inserting or removing AMC modules or slot filler panels.

FortiGate-5001A Security System Guide

 

01-30000-83456-20081023

21

Image 21
Contents FortiGate-5001A Page Contents For more information FortiGate-5001A security system Front panel LEDs and connectors Front panel LEDs and connectorsLists and describes the FortiGate-5001A LEDs LEDsConnectors Base backplane communicationFabric backplane communication FortiGate-RTM-XB2 AMC modulesFortiGate-ASM-FB4 Hardware installation SW11 Changing FortiGate-5001A SW11 switch settingsLocation of SW To change or verify the SW11 switch settingOpen FortiGate-5001A mounting componentsTo insert a FortiGate-5001A board into a chassis slot Inserting a FortiGate-5001A boardOpen the handles to their fully open positions FortiGate-5001A normal operating LEDs To remove a FortiGate-5001A board from a chassis slot Removing a FortiGate-5001A boardRemoving a FortiGate-5001A board Installing and removing AMC modules Resetting a FortiGate-5001A boardInserting AMC slot filler panels To install an AMC slot filler panelInserting AMC modules To insert an AMC module into a FortiGate-5001A boardTo remove an AMC module from a FortiGate-5001A board Removing AMC modulesTroubleshooting All chassis Firmware problemFortiGate-5001A does not start up FortiGate AMC modules not detected by FortiGate-5001A board To remove and reset an AMC moduleRegistering your Fortinet product Planning the configurationTransparent mode NAT/Route modeWeb-based manager Choosing the configuration toolFactory default settings Configuring NAT/Route modeCommand Line Interface CLI To configure interfaces Go to System Network Interface Using the web-based manager to configure NAT/Route modeTo configure the Default Gateway Using the CLI to configure NAT/Route modeUsing the web-based manager to configure Transparent mode Configuring Transparent modeTo switch from NAT/Route mode to transparent mode Using the CLI to configure Transparent modeTo upgrade the firmware using the web-based manager To upgrade the firmware using the CLIUpgrading FortiGate-5001A firmware FortiGate-5001A base backplane data communication CLI FortiGate-5001A fabric backplane data communication To power off a FortiGate-5001A board Powering off the FortiGate-5001A boardPowering off the FortiGate-5001A board Customer service and technical support Fortinet documentationRegister your Fortinet product Regulatory compliance Trademarks

5001A-SW, 5001A-DW specifications

Fortinet's FortiGate 5001A is a high-performance, next-generation firewall designed to meet the demands of large enterprises and data centers. The model comes in two distinct configurations—the 5001A-DW for data center workloads and the 5001A-SW for enhanced security capabilities.

The 5001A-DW is specifically tailored for critical data center environments, offering robust security and seamless integration into virtualized infrastructures. Its hardware design accommodates high capacity and throughput, beneficial for managing large volumes of data without compromising on security. This variant supports advanced networking technologies, such as Software-Defined Networking (SDN) and Network Function Virtualization (NFV), making it a versatile solution for organizations looking to optimize their network performance.

On the other hand, the 5001A-SW focuses more on advanced threat protection, integrating Fortinet’s FortiOS operating system, which provides comprehensive and consolidated security features. This model is engineered to safeguard against sophisticated cyber threats through its AI-powered security analytics and automated response capabilities. With an array of built-in security features, including IPS (Intrusion Prevention System), Application Control, and Web Filtering, the 5001A-SW enhances visibility and control over the network environment.

Both models provide exceptional SSL inspection capabilities, allowing organizations to analyze encrypted traffic without latency. With Fortinet's Security Fabric technology, the 5001A series offers integrated security across various network layers, streamlining security management and improving response times to threats.

The appliances also support advanced routing protocols and capabilities like Virtual Routing and Forwarding (VRF) to facilitate complex network designs. Their flexibility in deployment makes them suitable for a variety of environments, whether on-premises or in the cloud.

In terms of performance, the FortiGate 5001A series boasts impressive throughput rates, ensuring that organizations can scale their security measures in line with their growth. They are designed to minimize downtime, allowing for continuous and uninterrupted security operations.

Overall, the Fortinet FortiGate 5001A-DW and 5001A-SW models stand out for their scalability, advanced threat protection, and robust performance, positioning them as essential tools for organizations seeking to fortify their defenses against evolving cyber threats in today's digital landscape.