Enterasys Networks BRIM-E6 manual United States Government Restricted Rights

Page 5

NOTICE

2.NO LIABILITY FOR CONSEQUENTIAL DAMAGES. IN NO EVENT SHALL CABLETRON OR ITS SUPPLIERS BE LIABLE FOR ANY DAMAGES WHATSOEVER (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF BUSINESS, PROFITS, BUSINESS INTERRUPTION, LOSS OF BUSINESS INFORMATION, SPECIAL, INCIDENTAL, CONSEQUENTIAL, OR RELIANCE DAMAGES, OR OTHER LOSS) ARISING OUT OF THE USE OR INABILITY TO USE THIS CABLETRON PRODUCT, EVEN IF CABLETRON HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. BECAUSE SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, OR ON THE DURATION OR LIMITATION OF IMPLIED WARRANTEES IN SOME INSTANCES THE ABOVE LIMITATIONS AND EXCLUSIONS MAY NOT APPLY TO YOU.

UNITED STATES GOVERNMENT RESTRICTED RIGHTS

The enclosed product (a) was developed solely at private expense; (b) contains “restricted computer software” submitted with restricted rights in accordance with Section 52227-19

(a)through (d) of the Commercial Computer Software - Restricted Rights Clause and its successors, and (c) in all respects is proprietary data belonging to Cabletron and/or its suppliers.

For Department of Defense units, the product is licensed with “Restricted Rights” as defined in the DoD Supplement to the Federal Acquisition Regulations, Section 52.227- 7013 (c) (1) (ii) and its successors, and use, duplication, disclosure by the Government is subject to restrictions as set forth in subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer Software clause at 252.227-7013. Cabletron Systems, Inc., 35 Industrial Way. Rochester, New Hampshire 03867

iv

BRIM-E6 USER’S GUIDE

Image 5 Contents
Cabletron SYSTEMS, P. O. Box 5005, Rochester, NH BRIM-E6 USER’S GuideBRIM-E6 USER’S Guide DOC Notice FCC NoticeCabletron Software Program License Exclusion of Warranty and Disclaimer LiabilityCabletron SYSTEMS, INC Program License Agreement United States Government Restricted Rights Table of Contents Contents Chapter Introduction Using this ManualBRIM-E6 Overview BRIM-E6 FeaturesGetting Help Epim Media Type Connector BRIM-E6 SpecificationsEthernet Bridging Ethernet Bridging Related Manuals Unpacking the Brim Chapter InstallationInstalling BRIMs Removing the Coverplate Installing a BRIM-E6 in a MIMInstalling the Brim Installing a Brim in a Hub Installing an Epim into the Brim Connecting a UTP Segment to an EPIM-T Chapter Connecting to the NetworkConnecting the Brim to the Network Connecting to the Network Connecting the Brim to the Network EPIM-F1, EPIM-F2 and EPIM-F3 Connecting a Thin-Net Segment to an EPIM-C EPIM-C To connect an EPIM-A to an external network segment Connecting an AUI Cable to an EPIM-AConnecting an AUI Cable to an EPIM-X EPIM-X Finishing the InstallationSTB Standby Chapter Using the Lanview LedsEPIM-T 10BASE-T Twisted Pair Port Appendix a Epim SpecificationsEPIM-F1 and EPIM-F2 Multimode Fiber Optic Ports Parameter Typical Minimum Maximum EPIM-F3 Single Mode Fiber Optic PortParameter Typical Figure A-4. EPIM-C with BNC Port EPIM-C BNC PortEPIM-A and EPIM-X AUI Ports 1 10BASE-T UTP and STP Cable Requirements Appendix B Epim Cable RequirementsCable Requirements Insertion Loss Cable Type Attenuation Maximum Cable Length FOIRL/10BASE-FL Multimode Fiber Optic Cable RequirementsIeee 802.3 Foirl FOIRL/10BASE-FL Single Mode Fiber Optic Cable Requirements4 10BASE-2 Thin-net Cable Requirements AUI Cable Requirements EPIM-T EPIM-X Index