Enterasys Networks RBT-8110 manual Regulatory Compliance Information

Page 4

Regulatory Compliance Information

Federal Communications Commission (FCC) Notice

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment uses, generates, and can radiate radio frequency energy and if not installed in accordance with the operator’s manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause interference in which case the user will be required to correct the interference at his own expense.

WARNING: Changes or modifications made to this device which are not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Safety and EMC Requirements

The RBT‐8110 meets the following safety and electromagnetic compatibility (EMC) requirements:

Item

Specification

 

 

Safety

UL 60950, CSA C22.2 No. 60950, EN 60950, IEC 60950

Electromagnetic Compatibility (EMC)

FCC: 47 CFR Parts 2 and 15, ICES-003, EN 55022, EN 61000-3-2,

 

EN 61000-3-3, EN 55024, AS/NZS CISPR 22, VCCI V-3

 

 

Industry Canada Notice

This digital apparatus does not exceed the class A limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications.

Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de la class A prescrites dans le Règlement sur le brouillage radioélectrique édicté par le ministère des Communications du Canada.

Class A ITE Notice

WARNING: This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

Clase A. Aviso de ITE

ADVERTENCIA: Este es un producto de Clase A. En un ambiente doméstico este producto puede causar interferencia de radio en cuyo caso puede ser requerido tomar medidas adecuadas.

Klasse A ITE Anmerkung

WARNHINWEIS: Dieses Produkt zählt zur Klasse A (Industriebereich). In Wohnbereichen kann es hierdurch zu Funkstörungen kommen, daher sollten angemessene Vorkehrungen zum Schutz getroffen werden.

Product Safety

This product complies with the following: UL 60950, CSA C22.2 No. 60950, 73/23/EEC, EN 60950, IEC 60950.

Seguridad del Producto

El producto de Enterasys cumple con lo siguiente: UL 60950, CSA C22.2 No. 60950, 73/23/EEC, EN 60950, IEC 60950.

Produktsicherheit

Dieses Produkt entspricht den folgenden Richtlinien: UL 60950, CSA C22.2 No. 60950, 73/23/EEC, EN 60950, IEC 60950.

ii

Image 4
Contents RoamAbout Page Enterasys Networks, Inc Minuteman Road Andover, MA Regulatory Compliance Information Electromagnetic Compatibility EMC Vcci Notice Enterasys Networks, Inc Firmware License Agreement Page Vii Viii Contents Page About This Guide Intended AudienceAssociated Documents Conventions Used in This GuideGetting Help Kit Contents RBT-8110 Wireless Switch OverviewFront Panel Controls and Indicators LED Physical Specifications Power SupplyChassis Back Panel Environmental Specifications Environmental Specifications Parameter DescriptionInstallation Safety InformationSafety Information Safety Information Rack Mounting ‐1 shows the RBT‐8110 front panel being attached to the rackMid-Mount Rack Mounting Installation Pre-Configuration Tasks ConfigurationWireless Switch Configuration Tasks Wireless Switch Configuration Tasks Quickstart Command Procedure Optionally, enable Telnet Configuring RoamAbout Wireless Switches Using Rasm Stage the Wireless Switch Example 2 Deployment Site Has No Dhcp and No DNS Enable the MSS DNS client Preparing the Network for Distributed Access Points Page Index