Dialogic DSI SPCI Network Interface Boards manual Maxsiflen

Page 44

6 Message Reference

		PARAMETER AREA
8	2	max_sif_len

10	2	l3_flags

12	4	pc

16	2	ssf

18	2	up_enable

20	2	link0_flags

22	2	link0_slc

24	4	link0_adj_pc

28	2	link0_stream

30	2	link0_timeslot

32	2	link1_flags

34	2	link1_slc

36	4	link1_adj_pc

40	2	link1_stream

42	2	link1_timeslot

44	2	link2_flags

46	2	link2_slc

48	4	link2_adj_pc

52	2	link2_stream

54	2	link2_timeslot

56	2	link3_flags

58	2	link3_slc

60	4	link3_adj_pc

64	2	link3_stream

66	2	link3_timeslot

Description:

This message must be the first message sent to the DSI SPCI Board once the SS7 software is running. It is used to configure all modules on the board for operation. The message contains signaling point codes for this signaling point and the adjacent signaling point(s), flags to permit various level 1, level 2, and level 3 run-time options to be selected and the physical link parameters.

Once the DSI SPCI Board has been configured, you must reset it before configuring it again.

The confirmation message (if requested) indicates success by status of zero. To ensure configuration is complete before subsequent messages are issued to the board, the user should always request a confirmation message and check the status for success.

44

Image 44

Contents Dialogic DSI Spci Network Interface Boards MarchCopyright and Legal Notice Contents Configuration Command Reference Message ReferenceTables Host Utilities 108Revision History Introduction Related DocumentationSpecification Product IdentificationCapability License ButtonsProtocol Dimensioning CapacityInstallation IntroductionHardware configuration Software Installation for WindowsBoard Option Switch / Link Settings Installing Development Package for WindowsName Description Files Installed on a System Running WindowsStarting the Windows Device Driver Clearing Windows 2000 Install Wizard Removing Development Package for Windows Software Installation for LinuxInstalling Development Package for Linux Files Installed on a System Running Linux Device Drivers from Source CodeSoftware Installation for Solaris Installing the Development Package for SolarisVerifying Device Driver Loading An example message isSolaris 10 Additional Commands Non-serviced interrupts reportsFiles Installed on a System Running Solaris Solaris 9 Interface Name CheckingSystem has to be rebooted to force the change to take effect Removing the Development Package for SolarisConfiguration and Operation Typical Telephony Systems ConfigurationsOverview System StructureFollowing abbreviations are used in the table Host Processes and UtilitiesIsdn User Part Telephony User PartSystem Configuration System Configuration File SyntaxGenerating a System Configuration File For Linux, these Forkprocess commands are mandatory For Solaris, these Forkprocess commands are mandatoryProtocol Configuration Using Individual Messages Protocol ConfigurationProtocol Configuration using the s7mgt utility Page Board Information Diagnostics Board Diagnostics Hardware ParametersParameters are as described below Parameter DescriptionGeographic Addressing Watchdog TimerUsing the CT bus Switching Model Static InitializationDynamic Operation Example Code Building and Sending SclistenMSG Page To run the system within the current console, enter Program ExecutionProgram Execution under Windows Program Execution under Linux To run it in the background enterProgram Execution under Solaris Developing a User ApplicationNmake /f ctu.mnt Hardware Control Messages General Configuration MessagesMessage Reference MTP Interface Messages Event Indication MessagesMessage Summary Table Message Summary0x3e18 General Configuration Messages SSD Reset RequestStatus Response Board Reset RequestNumboards Parameter Description Boardtype Phyid Codefile RunmodeBoard Status Indication FormatBoard Configuration Request Field Name Meaning Type MGTMSGCONFIG0 0x7F10 SrcDescription Event Type Value MeaningMaxsiflen Isolated from the other boards using the CT bus. The CT bus Parameter DescriptionMessage Reference Bit Data Rate Value Description General Module Identification Message Parameter Description MajrevMajor revision identifier for the object being queried MinrevRead Board Info Request Message TextSPCI2S or SPCI4 board Field Name Meaning Type Mgtmsgrbrdinfo 0x6f0d SrcValue Mnemonic Meaning Boardrev SwaSwb PrommajrevLIU Configuration Request Field Name Meaning Type Liumsgconfig 0x7e34Hardware Control Messages Dst Mvdtaskid RspreqLiutype LinecodeLine coding technique taken from the following table FrameformatCrcmode BuildoutFaw NfawRaigen Description RaigenClearmask Field Name Meaning Type Liumsgcontrol 0x7e35 LIU Control RequestParameter Description Aisgen Loopmode Description Diagnostic loop back mode taken from the following tableLoopmode LIU Read Configuration Request LIU Read Control Request LIU State Request Offset Size Name StateLIU CT bus Initialization Request Parameter Description StateCurrent state of the LIU from the following table State DescriptionParameter Description Liuid ScchannelTsmask Field Name Meaning Type Mvdmsgscdriveliu 0x7e18 SrcValue Mnemonic Description 0xff None Setup failed ModeCT bus Listen Request Offset Size Name Liuid Timeslot ScchannelTimeslot MvipinvalidtimeslotFixed Data Output Request Offset Size Name Liuid Timeslot PatternReset Switch Request PatternCT bus Connect Request Field Name Meaning Mvdmsgscconnect 0x7e1fLocalslot If a parameter is not required, it must be set to zeroLocalstream CT bus speed Source Slot Range SourcestreamSourceslot Deststream DestslotField Name Meaning Type Mvdmsgcnfclock 0x7e20 Src Configure Clock RequestParameter Description Busspeed Value Clock Mode ClkmodePllclksrc Value Bus speed No changeValue NETREF1 clock Mode Ref1modeConfigure Clock Priority Request Field Name Meaning Type Mvdmsgclockpri 0x7e21 SrcParameter Description Liunpri Event Indication Messages 2 s7mgt Completion Status Indication Parameter Description Board StatusResult of initial configuration coded as follows Clock Event IndicationParameter Description Completion Status Field Name Meaning Type Mvdmsgclkind 0x0e23 SrcParameter Description Event ID LIU Status Indication LiustatusStatus field in the message header is coded as follows Field Name Meaning Type Mvdmsgliustatus 0x0e01 Liuid SrcError Indication Value Mnemonic StateParameter Description Error Code Error Code is coded as shown in the following table6 MTP2 Level 2 State Indication Parameter Description Link StateEvent Code is coded as shown in the following table 7 MTP2 Q.752 Event IndicationParameter Description Event Code Excessive delay of acknowledgement Excessive error rate SuermOnset of signaling link congestion Abatement of signaling link congestion8 MTP3 Q.752 Event Indication Offset Size Name Len Event specific parametersValue Mnemonic Paramter Description MtpevajspokPhysical Interface Parameters Configuration Command Reference1 SS7BOARD Command Bit CT Bus Clocking Mode Liuconfig Command Runmode Protocols selected to Run on the BoardCrcmode CRC mode taken from the following table Frameformat Frame format taken from the following tableLiuscdrive Command BoardidScbuslisten Command MTP Global Configuration MTP ParametersReserved1, reserved2 OptionsMTP Signaling Link MTP Link SetLinkid LinkrefSlc BlinkMTP Route DpcNormls Blink Serial PortSecondls UserpartmaskMTP User Part Global Isup ConfigurationIsup Parameters Isup Circuit Group Configuration Cicmask UserinstOpc VariantTUP Parameters Global TUP ConfigurationGlobal configuration parameters for the TUP module TUP Circuit Group Configuration Configuration parameters for a group of TUP circuits107 Command Line Options Host UtilitiesSsds DescriptionMmodule id Kconfig fileS7mgt Example Inotify module id