Canton 3C16476CS manual Montagesatz Anweisungen, Inserting the Screws

Page 15

To rack-mount the Switch:

1Place the unit the right way up on a hard, flat surface with the front facing towards you.

2Locate a mounting bracket over the mounting holes on one side of the unit.

3Insert the two screws supplied in the mounting kit and fully tighten with a suitable screwdriver.

Figure 2 Inserting the Screws

4Repeat the two previous steps for the other side of the unit.

5Insert the unit into the 19-inch rack and secure with suitable screws (not provided). Ensure that the ventila- tion holes are not obstructed.

6Reconnect the network cables.

Rack-Mounting or Free-Standing

15

Montagesatz Anweisungen

Der Switch wird mit zwei Halterungen und vier Schrauben geliefert. Diese werde für den Einbau in einen Baugruppenträger benutzt. Bei der Montage der Baugruppe beachten Sie die Anweisungen aus “Aufstellen des Switch“.

Der Switch ist eine Baueinheit hoch und passt in einen Standard 19'' (Zoll) Baugruppenträger.

ACHTUNG: Entfernen Sie alle Kabel, bevor Sie fort- fahren. Entfernen Sie die selbstklebenden Polster (Füße) von der Unterseite der Baugruppe, falls diese bereits angebracht sind.

1Plazieren Sie die Baugruppe aufrecht auf einer harten, ebenen Fläche mit der Vorderseite zu Ihnen.

2Ordnen Sie eine der Halterungen über den Löchern an der Seite der Baugruppe an.

3Stecken Sie zwei der mitgelieferten Schrauben in die Löcher und drehen Sie diese mit einem geeigneten Schraubendreher fest.

4Widerholen Sie letzten beiden Schritte auf der anderen Seite der Baugruppe.

5Führen Sie die Baugruppe in den 19" (Zoll) Baugrup- penträger ein und sichern sie die Baugruppe mit geeigneten Schrauben. (Nicht im Lieferumfang enthalten.)

6Schließen Sie alle Kabel wieder an.

Image 15

Contents 3C16476CS Baseline Switch 2250 PlusEnd of Life Statement Regulated Materials StatementEnvironmental Statement about the Documentation Contents Safety Information Conventions Icon DescriptionConvention Description Documentation Comments Related DocumentationAutonegotiating 10/100 Mbps Ports Overview of the Baseline Switch 2250 PlusFeatures and Capabilities Autosensing of MDI/MDIX ConnectionsPriority Level SFP PortsTraffic Prioritization Forwarding of Bpdu PacketsPhysical Features Front Panel48 RJ-45 Ports 10/100/1000BASE-T/SFP Ports Link/Activity LEDsStatusMeaning Status Meaning Module Active LEDsPackage Contents Before You Begin Positioning the SwitchAufstellen des Switch Using the Mounting KitRack-Mounting or Free-Standing Inserting the Screws Montagesatz AnweisungenColor State Supplying Power to the SwitchPlacing Units On Top of Each Other Checking for Correct OperationConnecting Devices to the Switch Connecting a Network DeviceUsing SFP Transceivers Approved SFP TransceiversInserting an SFP Transceiver Performing Spot Checks Removing an SFP TransceiverVerify That Installing the Switch Running the Discovery Application Requirements for Accessing the Web InterfaceWelcome screen of Discovery appears Logging On to the Web Interface Navigating the Web InterfaceMenu Menu Item Description Lists the available items on the menuNavigating the Web Interface ButtonsAccessing the Interface Without Using Discovery Dhcp Assigned IP AddressManually Assigned Static IP Address Configuration Overview Device Summary InformationDevice View Color Key Polling IntervalAdministration Settings Modifying the IP Address SettingsAutomatic IP Configuration IP Setup Backup ConfigurationRestore Configuration Initialize Firmware UpgradeReboot System AccessUser Summary Create User Modify UserRemove User Snmp Add SetupSystem Time SummarySnmp Remove Configuring VLANsModify Vlan VlanModify Vlan Screen Modify PortRemove RenameForwarding Tagged/Untagged Frames Port DetailVlan Detail Sample Vlan Configurations Setting Up Two VLANs on the Same SwitchSetting Up Vlan Across Two Switches Spanning Tree Tagged Vlan ConfigurationIgmp Query Igmp SnoopingConfiguring Port Settings AdministrationBroadcast Storm Detail Port Administration Summary ScreenLink Aggregation Speed/Duplex for 1000 Mbps ConnectionsCreate Guidelines for Creating TrunksModify Spanning Tree per PortSpanning Tree Summary Screen Spanning Tree Detail Screen Port MirroringPort Mirroring Screen QoS VoIP Traffic SettingsQoS VoIP Setup Screen Port SetupOUI Modify OUI SummaryConfigure SecurityRadius Client Radius Client Configure Screen 802.1X Settings802.1X Setup Screen Cable Diagnostics MonitoringAddress Table Cable Diagnostic Screen DiagnosticsConfiguring the Switch Forgotten Password Resetting to Factory DefaultsLink/Activity LED is on, but network perfor- mance is poor Solving LED IssuesForgotten Static IP Address Fiber cable is connected, but the Module Active LED is offAll ports appear to show continual activity If the Problem PersistsTroubleshooting Purchase Value-Added Services Troubleshoot Online Access Software DownloadsRegister Your Product Contact Us Telephone Technical Support and RepairCountry Country Telephone NumberUS and Canada Telephone Technical Support and Repair Important Safety Information Safety InformationAppendix B Safety Information Electrical Related StandardsEnvironmental PhysicalAppendix C Technical Information Category 3 cable 1000BASE-TAutonegotiation BandwidthEthernet Category 5e cablesCategory 6 cable ClientLayer Ieee 802.1pIeee 802.3ad IP AddressProtocol SwitchNetwork PingTrunking Traffic monitoringGlossary Index Index Regulatory Notices