Datalogic Scanning 1000I manual Keyboard Wedge

Page 57

Interface Features

Keyboard Wedge — cont.

START / END

PROGRAMMING BARCODES

Italy

Norway

Portugal

Spain

Sweden

Switzerland

Japan 106 Key

Hungary

Czech

Product Reference Guide

3-31

Image 57

Contents MagellanTM Datalogic Scanning, Inc Table of Contents Magellan Iii Datamatrix Length 1, Length 2 Programming Instructions Manual Conventions About This ManualCable To Host/Terminal Connect Here Connecting the ScannerResetting the Standard Product Defaults Using the Programming BarcodesProgramming Green LED Indications LED and Beeper IndicatorsError Error CodesMagellan Double Read Timeout General FeaturesDouble Read Timeout Productivity Index Reporting PIR Label Gone TimeoutSleep Mode Sleep Mode Power On Alert Good Read When to Indicate Good Read Beep Frequency Good Read Beep ControlSpecifies the duration of a good read beep Good Read Beep LengthGood Read Beep Volume Scanning Features Target Mode Active TimeTargeted Scanning Mode Target Mode Linger Time Wake Up Intensity Wake Up Intensity Interface Related Features Keyboard Wedge Interface Reference Interface Selection Interface Selection Keyboard Wedge P Keyboard Wedge Q Interface Selection Obey/Ignore Host Commands Interface FeaturesHost Transmission Buffers Interface FeaturesRS-232 Interface Features RS-232 Interface Features Hardware Flow Control Intercharacter Delay Software Flow Control Intercharacter DelayHost Echo Host Echo Quiet Interval Host Echo Quiet Interval Signal Voltage Normal/TTLBeep on Ascii BEL RS-232 InvertBeep on Not on File ACK NAK Options NAK Character ACK CharacterACK NAK Timeout Value Retry on ACK NAK TimeoutACK NAK Retry Count ACK NAK Error Handling USB-OEM Interface Features Transmission Failure IndicationUSB-OEM Device usage IBM Transmit Labels in Code 39 Format IBMSupported Symbologies Wand EmulationWand Emulation Barcode Format Wand Idle State Bar/Space PolarityTransmit Trailing Noise Signal SpeedTransmit Leading Noise Symbology ConversionKeyboard Wedge USB Keyboard Keyboard Wedge Caps Lock State Disable Power-on Simulation Control Characters 010 100 msec USB COM Interface Set-up Please Keep In Mind Data Editing OverviewGlobal Prefix/Suffix Scan the END barcode to exit Programming ModeGlobal Prefix/Suffix AIM ID Label ID Position Options Label IDLabel ID Default Setting for this Feature FF 4646 hex Default Setting for this Feature F 46 hex Default Setting for this Feature G8 4738 hex Magellan Default Setting for this Feature % 25 hex Case Conversion 41423132FFFFFFFF Character ConversionMagellan Disable/Enable UPC-A SymbologiesUPC-A Check Digit TransmissionExpand UPC-A to EAN-13 UPC-A Minimum Reads Number System TransmissionUPC-A In-store Minimum Reads UPC-E Disable/Enable UPC-EUPC-E Number System DigitExpand to UPC-E to UPC-A Minimum Reads Expand UPC-E to EAN13Expand UPC/EAN to Gtin GtinEAN-13 Disable/Enable EAN-13EAN-13 Flag 1 Character EAN-13Minimum Reads EAN-8 Disable/Enable EAN-8EAN-8 Enable EAN Two-Label Add-ons Add-ons Disable/Enable GS1 DataBar Omnidirectional GS1 DataBar Omnidirectional / Stacked OmnidirectionalUCC/EAN 128 Emulation GS1 DataBar Omnidirectional / Stacked Omnidirectional Disable/Enable GS1 DataBar Expanded GS1 DataBar Expanded / Expanded StackedGS1-128 Emulation Length Control GS1 DataBar Expanded / Expanded StackedSet Length Minimum Reads Coupon Read Control This feature controls coupon readingGS1 DataBar Limited Disable/Enable GS1 DataBar LimitedGS1 DataBar Limited Disable/Enable Code CodeCheck Character Calculation Start/Stop Characters Check Character TransmitCode 39 Full Ascii Code Quiet Zones Code 39 Length 1, Length 2 Programming InstructionsCode 39 Stitching Pharmacode Disable/Enable PharmacodePharmacode Disable/Enable EAN Transmit Function Characters Length Control Code 128 Conversion to Code Code 128 Length 1, Length 2 Programming InstructionsCode 128 Stitching Disable/Enable Interleaved 2 Interleaved 2Check Digit Calculation Check Digit Transmit Interleaved 2Length Control Default Setting for this Feature Interleaved 2 of 5 Stitching Minimum Reads Disable/Enable Codabar CodabarCheck Character Verification Check Character Transmit Codabar Quiet Zones Codabar Length 1, Length 2 Programming InstructionsStart/Stop Character Transmission Start/Stop Character TypeCodabar Stitching Start/Stop Character MatchMinimum Reads Following options apply to the Code 93 symbology Code Code 93 Length 1, Length 2 Programming Instructions Code 93 Stitching Disable/Enable MSI/Plessey MSI/PlesseyCheck Digit Verification Number of Check Characters MSI/PlesseyLength Control MSI/Plessey Length 1, Length 2 Programming Instructions MSI/Plessey Stitching Minimum Reads Standard 2 Disable/Enable Standard 2Standard 2 Length Control Standard 2 of 5 Length 1, Length 2 Programming Instructions Standard 2 of 5 Stitching Minimum Reads Magellan 2D Symbologies & Advanced Decoding Features 2D Symbologies Length Control Default Setting for this Feature 01 Minimum Reads Datamatrix Disable/Enable DatamatrixDatamatrix Datamatrix Length 1, Length 2 Programming Instructions Minimum Reads How to Capture an Image Image CaptureCaptured Image Format Optical and Read Performance Parameters Scanner DimensionsElectrical Parameters Physical PropertiesEnvironmental Parameters Other ParametersStandard Cable Pinouts Primary Interface Cables RS-232IBM Port 5B/9B/17 Keyboard Wedge USB, USB Keyboard & USB COMAlpha-Numeric Pad Alpha-Numeric Pad Appendix D Defaults by SymbologyIBM Interfaces Interface Default ExceptionsRS-232 Wincor/Nixdorf Interface Default ExceptionsKeyboards Keyboard Model Cross Reference Appendix ETable E-2. Scanset 1 Function Key Map Table E-4.Scanset 3, 102-Key Function Key Map Table E-5. Scanset 3 122-Key Function Key Map Table E-6. Japanese DOS Function Key Map Table E-7. NEC 9801-Key Function Key Map Accepting RS-232 Commands Chapter F Host CommandsMagellan Chapter G Sample Symbols Sample Symbols Ascii Chart Datalogic Scanning, Inc

Related manuals

Manual 160 pages 40.26 Kb

Manual 44 pages 55.92 Kb