Juniper Networks
IDP250, IDP8200, IDP 800 IDP 75, 250, 800, and 8200 Installation Guide 54 Index
Specifications
Install
Manager Administrator’s Guide
Connecting Power
IDP Configuration Basics
Web Access for Documentation
Safety
Power Supplies
Sniffer Mode Passive
Page 68
IDP 75, 250, 800, and 8200 Installation Guide
54
Index
Page 67
Page 68
Image 68
Page 67
Page 68
Contents
Releases 4.1r2a April
Copyright Notice
Table of Contents
Chapter Adding the Sensor to NSM
Index
Page
Sniffer Mode Passive
List of Figures
Page
List of Tables
Page
About This Guide
Audience
Conventions
Icon Meaning Description
Requesting Technical Support
Web Access for Documentation
Documentation
Self-Help Online Tools and Resources
Opening a Case with Jtac
Page
Planning an Installation
Installation Roadmap
IDP Sensor Deployment Mode
IDP Configuration Basics
IDP Sensor Placement
Sniffer Mode Passive
Advantages and Disadvantages of Sniffer Mode Passive
Transparent Mode Inline Active
NetScreen-Security Manager
Page
Hardware Overview
IDP Sensors
IDP 800 Sensor
IDP 75 Sensor
IDP 250 Sensor
IDP 8200 Sensor
IDP 800 Front Panel
Configurable NIC States
Traffic Ports Forwarding Interfaces
Settings Modes Availability Description
Normal State
NIC Bypass State
NIC State Options
NICs Off State
NIC Bypass and Cable Choices
External Bypass Unit State
Power Supplies
Management Ports
Console Serial Port
Management Port
IDP Sensor Power Supplies
IDP Sensor LEDs
System Status LEDs
Management and High Availability Port LEDs
Traffic Port LEDs
Hard Drive LEDs on Front Panel
Hard Drive LED Definitions Front Panel LED Description
Power Supply LEDs on Back Panel
Power Supply LED Definitions Back Panel LED Description
Installing the Sensor
General Installation Guidelines
Required Tools
Mounting Using Device Rack Rails
Rack Mounting the IDP Sensor
Mounting Using Midmount Brackets
Rail with Hinged Rear Bracket
Connecting Power
RU Device IDP 75 Midmount Bracket
Configuring the IDP Sensor
Initial Configuration Options
Simple Configuration
Simple Configuration Settings
Simple Configuration Values
Advanced Configuration
Connecting to the Sensor
Using the Console Serial Port to Configure the Sensor
Type an IP address and press Enter Following text appears
Using the Management Port to Configure the Sensor
Connecting Directly Using the Management Port
Connecting Remotely Using the Management Port
Simple or Advanced Configuration Using the Management Port
QuickStart Simple Configuration
ACM Advanced Configuration
Manager Administrator’s Guide
Verifying Traffic Flow
Connecting Forwarding Interfaces
Connecting the High Availability Port
Adding the Sensor to NSM
Adding Your Sensor to NSM
Select Device is Reachable default
Add Device Wizard Connection Settings
Type ssh-keygen -l -f sshhostdsakey and press Enter
Checking the Status of Your Sensor
Add Device Wizard Importing the Device
Page
Loading a Sensor Image into NSM
Updating IDP Sensor Software Using NSM Firmware Manager
Updating Software on the Sensor
Upgrading Sensor Software
Updating IDP Sensor Software Without NSM
Reimaging the IDP Sensor
Page
Servicing the Device
Replacing a Power Supply IDP 800, and 8200 Only
Remove a Power Supply
Remove a Hard Drive
Install a Power Supply
Replacing a Hard Drive IDP 800 and 8200 Only
Install a Hard Drive
Hard Drive Latch in Closed Position
Page
Advanced Deployment Modes
Advanced Configuration
Bridge Mode
Bridge Mode
Advantages and Disadvantages of Bridge Mode
Router Mode
Advantages and Disadvantages of Router Mode
IDP High Availability Deployment Modes
Proxy-ARP Mode
Advantages and Disadvantages of Proxy-ARP Mode
Specifications
IDP 75 Technical Specifications
Physical Specifications Value
AC Power Specifications Nominal Value Acceptable Range
Power Cord Specifications Country
Specification Value
IDP 250 Technical Specifications
Environmental Specifications
IDP 800 Technical Specifications
IDP 8200 Technical Specifications
Immunity
Safety Compliance
EMI Compliance
Index
ACM
IDP 75, 250, 800, and 8200 Installation Guide 54 Index
Related manuals
Manual
84 pages
43.14 Kb
Top
Page
Image
Contents