B&B Electronics TPC-1261H user manual

Page 6

13.Never open the equipment. For safety reasons, the equipment should be opened only by qualified service personnel.

14.If one of the following situations arises, get the equipment checked by service personnel:

a. The power cord or plug is damaged.

b. Liquid has penetrated into the equipment.

c. The equipment has been exposed to moisture.

d. The equipment does not work well, or you cannot get it to work according to the user's manual.

e. The equipment has been dropped and damaged. f. The equipment has obvious signs of breakage.

15.DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT WHERE THE STORAGE TEMPERATURE MAY GO BELOW - 20° C (-4° F) OR ABOVE 60° C (140° F). THIS COULD DAM-

AGE THE EQUIPMENT. THE EQUIPMENT SHOULD BE IN A CONTROLLED ENVIRONMENT.

16.CAUTION: DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED. REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE RECOMMENDED BY THE MANUFACTURER, DISCARD USED BATTERIES ACCORD-

ING TO THE MANUFACTURER'S INSTRUCTIONS.

The sound pressure level at the operator's position according to IEC 704- 1:1982 is no more than 70 dB (A).

DISCLAIMER: This set of instructions is given according to IEC 704-1. Advantech disclaims all responsibility for the accuracy of any statements contained herein.

TPC-1261H User Manual

vi

Image 6
Contents TPC-1261H Copyright Acknowledgements This Manual Covers the Following ModelsProduct Warranty 1 year FCC Class a Technical Support and Assistance Safety Instructions Packing ListPage Contents Chapter Features in Windows XP Embedded Appendix D Accessory Kit Assembly Procedure Appendix G Fuse Specifications General Information Fanless Powerful Communication CapabilityIntroduction Bright DisplaySpecifications SafetyEnvironment Operating Temperature 0 ~ 50 C 32 ~ 122 F LCD SpecificationsTouchscreen Specifications Backlight 2 Ccfl Backlight Life Time 50,000 hoursPower I/O Ports ArrangementPanel Mounting Dimensions and Cutout Panel MountingDimensions Page System Setup Unpack the Package Install CompactFlash Memory Card Touchscreen Icon System Engine Mainboard Connectors & Jumper Settings Main Board Connectors Page Software Configuration VGA Driver Installation Device ManagerUpdate Driver Update Wizard-2 Update Wizard-4 Update Wizard-6 Advantech COM Driver Install 10 Pciicom Setup12 PCI Icom Installation 14 Update Driver 16 Update Driver 18 PCI-1602 Device Manager 19 PCI Serial port Device Manager 21 Update Driver 23 PCI-1602 Master Installation 25 PCI Serial Port Installation 27 PCI Serial Port Installation 29 PCI Serial Port Installation 31 Installation Complete Entertainment Encryption/Decryption Driver33 Install Wizard 35 Install Wizard Features Windows XP Embedded Features in Windows XP Embedded EWFHorm Advantech UtilitiesVersion Information Page Page Serial Port Settings Appendix a Serial Port Settings COM1/ COM2/ COM3 Connector DefinitionCOM4 Setting RS-232 RS-422 RS-485 Watchdog Timer Programming Appendix B Watchdog Timer Programming OverviewWatchdog Timer Programming Figure B.1 Watchdog timer programming procedureTable B.1 Watchdog Timer Registers Enable watchdog timer and set 10 sec. as timeout interval Example ProgramsEnable watchdog timer and set 5 minutes as timeout interval Enable watchdog timer to be reset by mouse Enable watchdog timer to be reset by keyboard Generate a time-out signal without timer counting Page Watchdog Timer Programming on WinCE Appendix C Watchdog Timer Program- ming on WinCE DeviceIOControlLpvoid lpOutBuffer Parameters How to Use the Control Code Ioctl WdtenableIoctlwdtgettimeout CTLCODEFILEDEVICEUNKNOWN,ID, METHODBUFFERED, Fileanyaccess ExamplesAppendixC Page Accessory Kit Assembly Procedure Appendix D Accessory Kit Assembly Procedure CompactFlash to IDE Transfer KitFigure D.3 CompactFlash Slot Figure D.6 Connect the CD-ROM via the IDE Cable HDD Kit Assembly Appendix E HDD Kit Assembly Ruggedized HDD KitFigure E.2 Required Parts Figure E.3 Opening the Top Figure E.5 Connectting the FPC with the HDD Figure E.7 Reverse side of the HDD holder Figure E.9 Mounting the cushions Figure E.11 Placing the HDD holder Internal HDD Kit Assembly Figure E.13 Fastening the HDD holderFigure E.15 Placing a screw into its rubber casing Figure E.17 Connecting the FPC cable Figure E.19 Laying in the HDD insulator Figure E.21 Re-fastening the cover Figure E.23 Fastening the PCI/104 bracket Touchscreen Installation Configuration Appendix F Touchscreen Installation & Configuration Driver InstallationFigure F.3 Install Wizard Uninstall the Driver Figure F.5 UninstallTouchscreen Calibration CalibrateFigure F.8 Standard Calibration Figure F.10 Advanced Calibration Figure F.11 Advanced Calibration Draw Figure F.13 DrawFigure F.14 Clear Screen OptionFigure F.15 Option Page Fuse Specifications Appendix G Fuse Specifications Fuse SpecificationsFuse Replacement