B&B Electronics TPC-1261H user manual Specifications, Safety

Page 13

1.2 Specifications

1.2.1 System Kernel

CPU: GeodeLink Control Processor LX800 500MHz

BIOS: Award 512KB flash memory

South Bridge: GeodeLink Control Processor CS5535

VGA: GeodeLink Control Processor LX800 500MHz

Ethernet: Realtek RTL8100BL; IEEE 802.3u protocol compatible

Watchdog Timer: W83627 watchdog timer; 1.6 second timeout period

IDE: 1 EIDE channel supports one CompactFlash socket onboard (Master) and one IDE interface harddrive (Slave)

1.2.2 I/O Ports

1 parallel port: supports EPP/ ECP modes

4 serial ports: RS-232 (COM1, COM2, COM3) and RS-232/422/485 (COM4)

1 RJ-45 Ethernet port

1 PS/2 port: 6-pin mini-DIN ports for keyboard and mouse

2 USB 2.0 Ports: compliant with USB 1.0 and 1.1.

1 PCI/104 slot

Note:

COM1 and COM2 only support half-duplex

 

(Maximum baud rate: 115.2Kbps)

1.2.3 Safety and Environment

Safety

FCC Class A

CE certificated

The front bezel is compliant with NEMA 4 and IP65

3

Chapter1

Image 13
Contents TPC-1261H This Manual Covers the Following Models Copyright AcknowledgementsProduct Warranty 1 year FCC Class a Technical Support and Assistance Packing List Safety InstructionsPage Contents Chapter Features in Windows XP Embedded Appendix D Accessory Kit Assembly Procedure Appendix G Fuse Specifications General Information Introduction Powerful Communication CapabilityFanless Bright DisplaySafety SpecificationsTouchscreen Specifications LCD SpecificationsEnvironment Operating Temperature 0 ~ 50 C 32 ~ 122 F Backlight 2 Ccfl Backlight Life Time 50,000 hoursI/O Ports Arrangement PowerPanel Mounting Panel Mounting Dimensions and CutoutDimensions Page System Setup Unpack the Package Install CompactFlash Memory Card Touchscreen Icon System Engine Mainboard Connectors & Jumper Settings Main Board Connectors Page Software Configuration Device Manager VGA Driver InstallationUpdate Driver Update Wizard-2 Update Wizard-4 Update Wizard-6 10 Pciicom Setup Advantech COM Driver Install12 PCI Icom Installation 14 Update Driver 16 Update Driver 18 PCI-1602 Device Manager 19 PCI Serial port Device Manager 21 Update Driver 23 PCI-1602 Master Installation 25 PCI Serial Port Installation 27 PCI Serial Port Installation 29 PCI Serial Port Installation Entertainment Encryption/Decryption Driver 31 Installation Complete33 Install Wizard 35 Install Wizard Features Windows XP Embedded EWF Features in Windows XP EmbeddedAdvantech Utilities HormVersion Information Page Page Serial Port Settings COM1/ COM2/ COM3 Connector Definition Appendix a Serial Port SettingsCOM4 Setting RS-232 RS-422 RS-485 Watchdog Timer Programming Overview Appendix B Watchdog Timer ProgrammingFigure B.1 Watchdog timer programming procedure Watchdog Timer ProgrammingTable B.1 Watchdog Timer Registers Example Programs Enable watchdog timer and set 10 sec. as timeout intervalEnable watchdog timer and set 5 minutes as timeout interval Enable watchdog timer to be reset by mouse Enable watchdog timer to be reset by keyboard Generate a time-out signal without timer counting Page Watchdog Timer Programming on WinCE DeviceIOControl Appendix C Watchdog Timer Program- ming on WinCELpvoid lpOutBuffer Parameters Ioctl Wdtenable How to Use the Control CodeIoctlwdtgettimeout Examples CTLCODEFILEDEVICEUNKNOWN,ID, METHODBUFFERED, FileanyaccessAppendixC Page Accessory Kit Assembly Procedure CompactFlash to IDE Transfer Kit Appendix D Accessory Kit Assembly ProcedureFigure D.3 CompactFlash Slot Figure D.6 Connect the CD-ROM via the IDE Cable HDD Kit Assembly Ruggedized HDD Kit Appendix E HDD Kit AssemblyFigure E.2 Required Parts Figure E.3 Opening the Top Figure E.5 Connectting the FPC with the HDD Figure E.7 Reverse side of the HDD holder Figure E.9 Mounting the cushions Figure E.11 Placing the HDD holder Figure E.13 Fastening the HDD holder Internal HDD Kit AssemblyFigure E.15 Placing a screw into its rubber casing Figure E.17 Connecting the FPC cable Figure E.19 Laying in the HDD insulator Figure E.21 Re-fastening the cover Figure E.23 Fastening the PCI/104 bracket Touchscreen Installation Configuration Driver Installation Appendix F Touchscreen Installation & ConfigurationFigure F.3 Install Wizard Figure F.5 Uninstall Uninstall the DriverCalibrate Touchscreen CalibrationFigure F.8 Standard Calibration Figure F.10 Advanced Calibration Figure F.11 Advanced Calibration Figure F.13 Draw DrawOption Figure F.14 Clear ScreenFigure F.15 Option Page Fuse Specifications Fuse Specifications Appendix G Fuse SpecificationsFuse Replacement