Zhone Technologies 4929 DSLAM manual EMI Notices, United States EMI Notice

Page 5

transponders have been installed. Do not install laser products whose class rating is greater than 1. Refer to all important safety instructions that accompanied the transceiver prior to installation. Only laser Class 1 devices certified for use in the country of installation by the cognizant agency are to be utilized in this product. Also, laser warnings are to be provided in accordance with IEC 60825-1 and its Amendments 1 and 2, as well as 21 CFR 1010 and 1040.10(g).

10.General purpose cables are described for use with this product. Special cables, which may be required by the regulatory inspection authority for the installation site, are the responsibility of the customer. To reduce the risk of fire, use a UL Listed or CSA Certified, minimum No. 26 AWG (0.128 mm2) telecommunication cable, or comparable cables certified for use in the country of installation.

11.The equipment is intended for installation in a maximum 149° F (65° C) ambient temperature, in an environment that is free of dust and dirt.

12.Do not physically stack more than eight (8) units high. Physical stability has not been evaluated for stacking higher than eight units, and any configuration greater than eight may result in an unstable (tip-over) condition. Ensure that the four (4) rubber feet supplied with the product have been installed on the bottom of each unit prior to stacking any 4929 units on top of one another.

13.In addition, if the equipment is to be used with telecommunications circuits, take the following precautions:

Never install telephone wiring during a lightning storm.

Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations.

Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface.

Use caution when installing or modifying telephone lines.

Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning.

Do not use the telephone to report a gas leak in the vicinity of the leak.

14.When installed in the final configuration, the product must comply with the applicable Safety Standards and regulatory requirements of the country in which it is installed. If necessary, consult with the appropriate regulatory agencies and inspection authorities to ensure compliance.

EMI Notices

!UNITED STATES – EMI NOTICE:

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

The authority to operate this equipment is conditioned by the requirements that no modifications will be made to the equipment unless the changes or modifications are expressly approved by the manufacturer.

If the equipment includes a ferrite choke or chokes, they must be installed per the installation instructions.

4929 DSLAM Installation and User’s Guide

5

Image 5
Contents Dslam Installation and User’s Guide Copyright 2005 Zhone Technologies, Inc. All rights reserved End User License Agreement Zhone and Affiliates Dslam Installation and User’s GuideImportant Safety Instructions United States EMI Notice EMI NoticesCanada EMI Notice CE MarkingContents Configuring Your Windows PC to Communicate with NMS 4929-A2-ZN20-30 Dslam Installation and User’s Guide Dslam Installation and User’s Guide Document Summary About this GuideDocument Purpose and Intended Audience GrandVIEW EMS User’s Guide Related Product DocumentsTechnical Support Contacting Global Service and SupportService Requirements Dslam Installation and User’s Guide Overview FeaturesIntroduction Introduction Preparation InstallationADSL2+ Cables RequiredPots SFPUnpacking the Hardware Package ContentsMounting Configurations Installing the Brackets for Rack Mounting Installing the Dslam Into a Rack Installing the Dslam on a Wall Installing the Dslam on a Wall Installing the Dslam on a Shelf or Desktop Cabling Overview CablingInstalling the Micro Interface Module Connecting the ADSL2+ and Pots Connectors Connecting the SFP Connector or the 10/100/1000 Connector Connecting DSLAMs to Each Other Connecting a Terminal or PC to the COM Port Connecting the COM PortConnecting a Modem to the COM Port Connecting to Power+48 VDC -48 VDC LED Meanings LED LocationsPWR Web Interface System Requirements Configuration Using the NMSNMS Configuring Your Windows PC to Communicate withNMS home page appears Dslam Management ConfigurationAdvanced Configuration Password Http PasswordSnmp Configuration Snmp Community Administration Global Set Global Circuit ConfigurationAccepted from source IP addresses in the ranges Global Dscp Rules Vlan Global IP Rules Specify a Vlan ID range. For each Global IP Global MAC Rules MAC Rule, if you selected Tag for Allow Tag Global Vlan Rules Specify a Vlan ID range that constitutes a Parameter Description Global Advanced Configuration EC/FDM Circuit SummaryCircuit Configuration Circuit Configuration Dscp Rules Parameter Description IP Rules Parameter Description MAC Rules Parameter Description Vlan Rules Vlan Backbone Vlan ID Parameter Description Port Statistics Copy Port SNR Advanced Configuration MAC-IGMP MAC and Igmp SummaryParameter Description Dslam Interconnect Configuration To specify the port connected to a downstream Dslam CLI System Requirements Command Line InterfaceConnecting a PC Directly Launching the Terminal Emulation Program CLI CommandsEnabletelnet DisablewebserverEnabletftp EnablewebserverDefaultgateway ClisessiontimeoutFlood UPL,VLN Generalpassword LAYER2ENABLESuperuserpassword ResetMAC MgmtportuplinkUsing the CLI to Establish Inband Management Downloading MIBs Snmp InterfaceSnmp Community Strings Access Community StringDSL Ports and Pots Splitter Connectors Connectors and PIN AssignmentsDSL Connector Pinouts Sheet 2 MOD-DEF2 I2CDATA MOD-DEF1 I2CCLK MOD-DEF0 Sfppresentl SFP ConnectorLOS RD+10/100/1000BaseT Connector DSR RTS DB9 to RJ45 Adapter PinoutsGND DTR CTSConnectors and Pin Assignments Equipment List Equipment List Technical Specifications Ieee 802.1Q Vlan CLI IndexNumerics Igmp Snmp Tftp Vlan ID

4929, 4929 DSLAM specifications

Zhone Technologies, a leading provider of innovative networking and communications equipment, has garnered attention for its advanced digital subscriber line access multiplexer (DSLAM), the Zhone 4929. This model is designed to meet the growing demand for high-speed broadband access in a variety of environments, making it a vital component in modern telecommunications networks.

One of the primary features of the Zhone 4929 DSLAM is its ability to support multiple DSL standards, including ADSL, ADSL2, ADSL2+, and VDSL2. This versatility enables service providers to efficiently manage a diverse range of customer demands and to optimize bandwidth allocation across various service tiers. The ability to support both asymmetric and symmetric DSL technologies allows operators to cater to different business and residential requirements while maintaining service quality.

The Zhone 4929 is equipped with advanced hardware that supports high-density deployments, allowing network operators to maximize their investment in infrastructure. With support for up to 384 DSL lines in a single chassis, this DSLAM can easily scale to accommodate growing subscriber bases. This flexibility is essential for service providers aiming to expand their coverage and reach without significantly increasing operational costs.

Another notable characteristic of the 4929 is its robust management capabilities. It features an intuitive management interface that simplifies the monitoring and configuration of the device, enabling operators to efficiently manage their networks. With real-time performance monitoring and diagnostic tools, service providers can quickly identify and resolve issues, ensuring a high-quality end-user experience.

Power efficiency is also a key aspect of the Zhone 4929 design. The DSLAM employs energy-efficient technologies that reduce overall power consumption, making it not only environmentally friendly but also cost-effective during operation. This is particularly important in an era where operational costs and sustainability concerns are at the forefront of industry challenges.

Moreover, the Zhone 4929 is designed with future-proofing in mind. Its modular architecture allows for easy upgrades and expansions, meaning that service providers can adapt to new technologies and standards as they emerge, protecting their investments over time.

In conclusion, the Zhone Technologies 4929 DSLAM is a powerful solution for enhancing broadband access. Its support for multiple DSL technologies, high-density capabilities, robust management tools, energy efficiency, and future-proof design make it an essential component for any service provider looking to deliver high-speed internet access in today's fast-paced digital world.