BEA Multibeam Receiving and communication module, First receiver head wiring, Emitting module

Page 2

FUNCTIONNAL Functional wiring structure:

DESCRIPTION

Controller

Communication and supply

Receiving module

Receivers

Receiving module

Receivers

5 wires

Emitting module Address 1

16 times

Emitters

Emitting module Address 2

16 times

Emitters

WIRINGAND INSTALLATION

On the receiving module 16 red LEDs show the status of each beam. Plug connectors with 3.5 mm pitch are used. The 2 twisted wires enable the connection of each head to the controller. The wires must be between 0.5 m and 5 m long. Thanks to the multiplexing of the heads, there is no interference between two heads.

The status information of the beams are transmitted to the controller via a RS485 communication. It is possible to connect other terminals (maximum 32) on this bus.

The 2 modules composing the system are housed in aluminum profiles that can be fixed with screws or with double-side adhesive.

A green LED on the emitting module indicates if the module is on. If the link between the 2 modules is not correct, the LED will remain off and the MULTIBEAM will not work properly.

A potentiometer on the emitting module allows to adjust them emission power in order to reduce the influence of one module to an other module in close proximity (turn clockwise = increase emission power).

The receiver has a green cable and the emitter a yellow cable. Wiring Diagram:

receiving and communication module

 

P1 SW1

P2

LEDS

16 Receiver head connectors

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

4 wires cable to controller

1--

GND

RS485-

RS485+

+24V

5 wires cable between the 2 modules Lmax = 5m

-- 5

 

 

 

 

IN

 

 

 

First receiver head wiring

 

 

 

 

 

 

 

 

 

 

 

 

 

 

GND

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Emitting module

 

 

 

 

 

 

 

 

 

 

P2 Potentiometer

 

16 emitter head conectors

 

 

 

Status LED

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

OUT

GND First emitter head wiring

1-- - 5

Image 2
Contents Microcell Control boxesReceiving and communication module First receiver head wiringGND First emitter head wiring Emitting moduleHardware SoftwareSTX ETX