Belkin F5D9630-4 user manual LAN Status LEDs, Wlan Status LED

Page 11

Knowing your Router

2. LAN Status LEDs

These LAN Status LEDs are labeled 1–4 and correspond to the numbered ports on the rear of the Router. When a computer is properly connected to one of the LAN ports on the rear of the Router, the LED will light. Solid GREEN means a computer or a network-enabled device is connected. When information is being sent over the port, the LED blinks rapidly. ORANGE indicates a 10Base-T connection.

 

 

 

Orange

Ethernet link is up and 10Base-T

 

 

 

 

device connected

 

 

 

 

 

 

 

 

Orange - blinking

10Base-T device is transmitting or

 

 

 

 

receiving data

 

 

 

 

 

 

 

 

Green

Ethernet link is up and 100Base-T

 

 

 

 

device is connected

 

 

 

Green - blinking

100Base-T device is transmitting or

 

 

 

 

receiving data

 

 

 

 

 

3. WLAN Status LED

The WLAN Status LED is solid GREEN when you enable the wireless LAN function. It flashes when the Router is transmitting or receiving data wirelessly.

 

Green

WLAN is up and connected

 

 

 

 

Green - blinking

Transmitting or receiving data

 

 

 

4. ADSL LED

The ADSL LED flashes GREEN during negotiation with your ISP. It stays GREEN when the Router is connected properly to your ADSL service.

 

OFF

No ADSL connection

 

 

 

 

Green - blinking

Negotiating connection

 

 

 

 

Green

ADSL link is up and connected

 

 

 

1

2

3

4

5

6

7

8

9

10

section

9

Image 11
Contents Wireless G+ Mimo ADSL2+ Modem Router Table of Contents Introduction Advantages of a Wireless NetworkIntroduction Placement of your Wireless G Plus Mimo ADSL2+ Modem RouterImportant Factors for Placement and Setup Router PlacementCordless Phones Choose the Quietest Channel for your Wireless NetworkAvoid Obstacles and Interference Secure Connections, VPNs, and AOL Product Overview Product FeaturesProduct Overview System Requirements Package ContentsSetup Assistant Software System Requirements Knowing your RouterNetwork Status Display Front Panel Power LEDKnowing your Router Wlan Status LED LAN Status LEDsEthernet Ports Internet LEDBack Panel DSL Line Power Plug Reset ButtonConnecting and Configuring your Router Replacing an Existing Modem or Modem Router Set Up the Router Run the Setup Assistant SoftwareConnecting and Configuring your Router Section Connecting and Configuring your Router Connecting and Configuring your Router Connecting and Configuring your Router Congratulations Optional Assistance Connecting Other Computers TroubleshootingCongratulations Hardware Connections Follow the Quick Installation Guide Alternate Setup MethodHome Button Logging out of the RouterUnderstanding the Web-Based Advanced User Interface Quick-Navigation LinksAlternate Setup Method Connection Type Setting your ISP Connection Type to PPPoE or PPPoA Alternate Setup Method Setting your Connection Type to Dynamic IP 1483 Bridged Setting your ISP Connection Type to Static IP IPoA Setting Custom Domain Name Server DNS Settings Setting up the Router’s Dynamic DNS Update Client Using Dynamic DNSAlternate Setup Method Viewing the LAN Settings Using the Web-Based Advanced User InterfaceChanging LAN Settings Using the Web-Based Advanced User InterfaceViewing the Dhcp Client List Using the Web-Based Advanced User InterfaceWi-FiMultimedia WMM Settings Configuring the Wireless Network SettingsChanging the Wireless Channel Changing the Wireless Network Name Ssid802.11g + 802.11b Using the Wireless Mode SwitchWPA2 Requirements Setting WPA/WPA2-Personal PSK Setting WPA-PSK Setting WPA SecuritySetting WPA-Enterprise Radius Settings Setting WPA2-Enterprise Radius Settings Setting WEP EncryptionUsing a Hexadecimal Key Wireless Bridge Configuring Internal Forwarding Settings Configuring the FirewallChoosing an Application Manually Entering Settings into the Virtual ServerSetting MAC-Address Control Setting Client IP FiltersBlocking an Icmp Ping Enabling the Demilitarized Zone DMZSecurity Log Restarting the Router Restarting the Router to Restore Normal OperationUtilities Restoring Factory Default Settings Saving a Current Configuration Restoring a Previous Configuration Downloading a New Version of Firmware Updating the FirmwareChecking for a New Version of Firmware Using the Web-Based Advanced User Interface Updating the Router’s Firmware Changing the Login Time-Out Setting Changing System SettingsSetting or Changing the Administrator Password Enabling Remote Management Setting the Time and Time ZoneUsing the Web-Based Advanced User Interface Enabling/Disabling UPnP Enabling/Disabling Auto Firmware UpdateManually Configuring Network Settings in Mac OS up to Manually Configuring Network SettingsManually Configuring Network Settings Manually Configuring Network Settings in Mac OS Manually Configuring Network Settings Manually Configuring Network Settings in Windows 98 or Me Manually Configuring Network Settings Microsoft Internet Explorer 4.0 or Higher Recommended Web Browser settingsRecommended Web Browser Settings Recommended Web Browser settings Netscape Navigator 4.0 or Higher Solution TroubleshootingProblem Setup Assistant cannot connect my Router to the Internet Troubleshooting Can’t connect to the Internet wirelessly Troubleshooting Troubleshooting C3 03 0F AF 4B B2 C3 D4 4B C3 D4 E7 E4 = 128-bit key Troubleshooting Click OK, and then Apply to save the settings Troubleshooting XP WPA Wireless Comparison Chart Technical Support Belkin Technical SupportFCC Statement InformationModifications InformationSection Free Tech Support