ADTRAN 1200153L1, 3360.9VU01, 1200153L2, XRT Channelunacceptable, Dest not Isdn, Destoutoforder

Page 80

Appendix C. Status Buffer Messages

CHANNEL_UNACCEPTABLE

The channel requested has not been subscribed.

CID>0 rcvd

Received an incoming call from a third party during negotiations with a far-end BONDING unit on the use of the second Bearer channel.

Connect Timeout

Call attempt does not connect in x amount of time.

DEST NOT ISDN

The number called is not ISDN (warning only).

DEST_OUT_OF_ORDER

The called number is out of order.

Dial

The Express XR/XRT placed a call on either the first or second channel. The number called is displayed following the message.

Disconnect

The call on either the first or second channel was disconnected from the network. The far-end phone number is displayed if available. Ensure flow control setting match on both terminal adapters.

Disconnect Req

Far-end unit disconnected during BONDING negotiation.

DTR not up

Express XR/XRT tried to place a call in a dialing mode that requires DTR to be in an active state, but it is not.

Dump call

The Express XR/XRT could not accept an incoming call because it was already involved in a call.

Dump

An incoming call on either the first or second channel was discarded by the Express XR/XRT. The calling number is displayed if available.

68

Express XR/XRT Quick Start Guide

61200.153L1-1

Image 80
Contents Express XR/XRT Trademarks Table of Contents Canadian Emissions Requirements Canadian Equipment LimitationsPage Adtran Telephone Company Contacts for Isdn Service NynexTable of Contents Table of Contents Installing an Analog Modem Application ConfigurationTroubleshooting Guidelines Appendix A. AT Commands and S-RegistersList of Tables List of FiguresTable of Contents Chapter Introduction Express XR/XRT OverviewBasic Rate Isdn Line Minimum RequirementsWhat You Provide Express XR/XRT Contents What Adtran ProvidesIntroduction Chapter Installation Verify Switch SettingsExpress XRT Only Connecting the Express XR/XRTDip Switches on Rear Panel Standard Isdn Internet/Remote Access Application Express XR/XRT Software InstallationGo to the Express XR/XRT Software Installation procedure Go to the Express Configuration Wizard Installation section Win 95/NT 4.0 Control Panel Modem InstallationMicrosoft Windows 95 and Windows NT Express Configuration Wizard InstallationSelect Adtran Express XR or XRT from the Drivers list Installation Options Go to the section Using the Express Configuration WizardGet On With It Microsoft Windows 3.1 and Windows NTWindows NT 3.51 INF File Installation Go to the section Express Configuration Wizard InstallationCall Waiting Basic Telephone ServiceSupplementary Voice Services Phone Number Allocation Single Phone Number OperationConference Calling Automatic RedialUsing the Express Configuration Wizard Adtran Express Configuration ScreenUnable to Auto-Detect Express Configuration Wizard Connection Tab Auto-Detect SPIDs/Switch Type Using the Express Configuration Wizard HelpExpress Configuration Wizard Tray Tool Express Configuration Wizard Tray ToolPreferences Tab Unknown State Express XRT Disabled, External Analog Modem EnabledExpress XR/XRT Enabled, External Analog Modem Disabled Express Configuration Tray Tool Menu Express Configuration Wizard Tray Tool MenuEnable/Disable Modem PropertiesExit Installing Windows 95 Dial-Up NetworkingAbout Macintosh Configuration VT 100 Terminal EmulationVT 100 Configuration VT 100 Terminal Configuration MenuVT 100 Terminal Status Buffer VT 100 Terminal Status Buffer MenuInstallation Chapter Installing an Analog Modem External Analog Modem ApplicationConnecting an External Analog Modem External Analog Modem ApplicationSelect Dont detect my modem I will select it from a list Installing a New External Analog ModemClick Connect External Modem Configuring an External Analog Modem Required External Analog Modem SettingsExpress Configuration Wizard Modem Enable Controlling an External Analog ModemExpress Configuration Wizard Connecting an External Modem No Modem Attached Error Message Express Configuration Wizard Modem DisableTerminal Emulation Modem Enable HyperACCESS Verifying External Modem ConnectionHyperACCESS Enabling an External Analog Modem Terminal Emulation Modem Disable Internal Analog Modem Application Internal Analog Modem ApplicationConnecting an Internal Analog Modem Chapter Application Configuration Factory Default ConfigurationProfile Configurations Factory Remote Access 64kFactory Internet 64k Factory Internet 128kExpress Configuration Wizard Starting the Express Configuration Wizard SoftwareInternet and Remote Access Factory Remote Access 128kCreating a Custom Profile Internet ConnectionDefining a User Program Button Choose either the User Program 1... or User ProgramDefining a Custom HyperACCESS Session BBS ApplicationsApplication Configuration Application Configuration Power/Line LED Flashes and B1 and B2 LEDs are Off Chapter TroubleshootingPower/Line LED is Off Power/Line LED, B1, and B2 LEDs Flash Green Dial-Up Connection ProblemsAuto-detect Switch/SPIDs Remains at Link Down Express XR/XRT Not DetectedDial-Up Networking Difficulty External Analog Modem Not DetectedDifficulty with 230.4 kbps Operation Appendix a AT Commands and S-Registers AT CommandsUsing an AT Command Using S-RegistersReading an S-Register Reading an S-Register StringChanging a String S-Register Dialing a Call using the AT Command ProcessorChanging an S-Register Command Function AT!ZClear-To-Send CTS Control Line Options AT Command Response Message Options Register List TimeS15 ... Async ................ Asynchronous Bonding method S25S27 S30S34 S32S33 S54 S42 ... BondS53 S58 S65S71 S72S118 . Chap Enable .... = Chap enabled SS89 SN9 LOCAppendix B LEDs LEDsTable B-A LEDAppendix B. LEDs Accessinfodiscarded Appendix C Status Buffer MessagesBadinfoelem BearcapnotavailBearercapnotauth Bonding +/-XXXBusy CallrejectedChandoesnotexist ChannotimplementedDestoutoforder ChannelunacceptableDest not Isdn Facilitynotimplement FacilitynotsubscribedFacilityrejected ID =Invalidelemcontents InvalidcallrefInvalidmsgunspec InvalidnumberformatNetwork Busy NetworkcongestionNetworkoutoforder NocircuitavailableProtocolerror NumberchangedOutgoingcallbarred PPP Compression UPServicenotavail TimerexpirySource not Isdn TemporaryfailureUnassignednumber UseralertnoansUserbusy WrongmessageAppendix D Loop Status Messages Yyyy PPPAppendix E Connector Pinouts RS-232 InterfaceTable E-A Pin Name DescriptionModem Interface Table E-BTable E-C RJ-11 Pots Port InterfacesTable E-D RJ-45 Isdn Line InterfaceAppendix E. Connector Pinouts Register now to be included in our Preferred Customer DatabaseExpress XR/XRT Warranty Registration Card