ADTRAN 1200153L1, XRT Unassignednumber, Useralertnoans, Userbusy, Wrongmessage, Wrongmsgforstate

Page 86

Appendix C. Status Buffer Messages

UNASSIGNED_NUMBER

The phone number dialed does not exist.

Unknown AT cmd

User issued an unknown AT command.

USER_ALERT_NO_ANS

Ringing call is not answered.

USER_BUSY

The dialed number is busy.

V120 connected

The V.120 rate adaption successfully connected to the far-end unit.

V120 Timeout

V.120 negotiation failed.

WRONG_MESSAGE

Call control error.

WRONG_MSG_FOR_STATE

Call control error.

74

Express XR/XRT Quick Start Guide

61200.153L1-1

Image 86

Contents Express XR/XRT Trademarks Table of Contents Canadian Emissions Requirements Canadian Equipment LimitationsPage Adtran Telephone Company Contacts for Isdn Service NynexTable of Contents Table of Contents Troubleshooting Guidelines Installing an Analog ModemApplication Configuration Appendix A. AT Commands and S-RegistersList of Tables List of FiguresTable of Contents Chapter Introduction Express XR/XRT OverviewBasic Rate Isdn Line Minimum RequirementsWhat You Provide Express XR/XRT Contents What Adtran ProvidesIntroduction Chapter Installation Verify Switch SettingsExpress XRT Only Connecting the Express XR/XRTDip Switches on Rear Panel Standard Isdn Internet/Remote Access Application Express XR/XRT Software InstallationGo to the Express XR/XRT Software Installation procedure Go to the Express Configuration Wizard Installation section Win 95/NT 4.0 Control Panel Modem InstallationMicrosoft Windows 95 and Windows NT Express Configuration Wizard InstallationSelect Adtran Express XR or XRT from the Drivers list Get On With It Installation OptionsGo to the section Using the Express Configuration Wizard Microsoft Windows 3.1 and Windows NTWindows NT 3.51 INF File Installation Go to the section Express Configuration Wizard InstallationCall Waiting Basic Telephone ServiceSupplementary Voice Services Conference Calling Phone Number AllocationSingle Phone Number Operation Automatic RedialUsing the Express Configuration Wizard Adtran Express Configuration ScreenUnable to Auto-Detect Express Configuration Wizard Connection Tab Auto-Detect SPIDs/Switch Type Using the Express Configuration Wizard HelpExpress Configuration Wizard Tray Tool Express Configuration Wizard Tray ToolPreferences Tab Unknown State Express XRT Disabled, External Analog Modem EnabledExpress XR/XRT Enabled, External Analog Modem Disabled Enable/Disable Modem Express Configuration Tray Tool MenuExpress Configuration Wizard Tray Tool Menu PropertiesExit Installing Windows 95 Dial-Up NetworkingAbout Macintosh Configuration VT 100 Terminal EmulationVT 100 Configuration VT 100 Terminal Configuration MenuVT 100 Terminal Status Buffer VT 100 Terminal Status Buffer MenuInstallation Chapter Installing an Analog Modem External Analog Modem ApplicationConnecting an External Analog Modem External Analog Modem ApplicationSelect Dont detect my modem I will select it from a list Installing a New External Analog ModemClick Connect External Modem Configuring an External Analog Modem Required External Analog Modem SettingsExpress Configuration Wizard Modem Enable Controlling an External Analog ModemExpress Configuration Wizard Connecting an External Modem No Modem Attached Error Message Express Configuration Wizard Modem DisableTerminal Emulation Modem Enable HyperACCESS Verifying External Modem ConnectionHyperACCESS Enabling an External Analog Modem Terminal Emulation Modem Disable Internal Analog Modem Application Internal Analog Modem ApplicationConnecting an Internal Analog Modem Chapter Application Configuration Factory Default ConfigurationFactory Internet 64k Profile ConfigurationsFactory Remote Access 64k Factory Internet 128kInternet and Remote Access Express Configuration WizardStarting the Express Configuration Wizard Software Factory Remote Access 128kCreating a Custom Profile Internet ConnectionDefining a User Program Button Choose either the User Program 1... or User ProgramDefining a Custom HyperACCESS Session BBS ApplicationsApplication Configuration Application Configuration Power/Line LED Flashes and B1 and B2 LEDs are Off Chapter TroubleshootingPower/Line LED is Off Power/Line LED, B1, and B2 LEDs Flash Green Dial-Up Connection ProblemsAuto-detect Switch/SPIDs Remains at Link Down Express XR/XRT Not DetectedDial-Up Networking Difficulty External Analog Modem Not DetectedDifficulty with 230.4 kbps Operation Appendix a AT Commands and S-Registers AT CommandsReading an S-Register Using an AT CommandUsing S-Registers Reading an S-Register StringChanging a String S-Register Dialing a Call using the AT Command ProcessorChanging an S-Register Command Function AT!ZClear-To-Send CTS Control Line Options AT Command Response Message Options Register List TimeS27 S15 ... Async ................ Asynchronous Bonding methodS25 S30S34 S32S33 S54 S42 ... BondS53 S71 S58S65 S72S118 . Chap Enable .... = Chap enabled SS89 SN9 LOCTable B-A Appendix B LEDsLEDs LEDAppendix B. LEDs Accessinfodiscarded Appendix C Status Buffer MessagesBearercapnotauth BadinfoelemBearcapnotavail Bonding +/-XXXChandoesnotexist BusyCallrejected ChannotimplementedDestoutoforder ChannelunacceptableDest not Isdn Facilityrejected FacilitynotimplementFacilitynotsubscribed ID =Invalidmsgunspec InvalidelemcontentsInvalidcallref InvalidnumberformatNetworkoutoforder Network BusyNetworkcongestion NocircuitavailableOutgoingcallbarred ProtocolerrorNumberchanged PPP Compression UPSource not Isdn ServicenotavailTimerexpiry TemporaryfailureUserbusy UnassignednumberUseralertnoans WrongmessageAppendix D Loop Status Messages Yyyy PPPTable E-A Appendix E Connector PinoutsRS-232 Interface Pin Name DescriptionModem Interface Table E-BTable E-D Table E-CRJ-11 Pots Port Interfaces RJ-45 Isdn Line InterfaceAppendix E. Connector Pinouts Register now to be included in our Preferred Customer DatabaseExpress XR/XRT Warranty Registration Card