Multi Tech Equipment MTA128ST Features, Isdn BRI Line, Spid Service Profile ID, NT1 Connection

Page 5

Introduction and Description

Your ISDN TA is compatible with prevalent ISDN switch protocols. It communicates using ISDN BRI (2B+D) service, which provides up to 128K bps data communications. This manual documents the following models:

MTA1 28ST for S/T interface with one POTS port

MTA1 28NT for U interface with one POTS port

Some analog devices, including telephone set, answering machine, and modem, can be connected to the POTS port via an RJ-1 1 jack.

This User Guide will help you install, configure, and operate your terminal adapter.

Features

The MTA128ST/NT communicates over public ISDN telephone lines. Features include:

Compatibility with EuroISDN (ETSI/DSS1/NET3), French VN4, and Japanese INS64 switch protocols

Compatibility with U.S. NI-1, AT&T 5ESS, and DMS-100 switch protocols

Compatibility with V.120, ML-PPP, and X.75 protocols

Transparent synchronous communication capability (CLEAR)

ISDN BRI (2B+D) and analog ports

RS232E serial port

Serial port speeds to 460.8 Kbps

Support of PPP (Point-to-Point Protocol) for high speed ISDN connections

Tone detection to allow use of a standard telephone for ISDN line access (an ISDN telephone is not required)

Automatic detection of incoming calls as voice or data

Windows 98/NT/ME software utility and a firmware utility for easy ISDN line configuration

AT commands, S-registers, and result codes

Ability to use the same communications software as analog modems

Flash memory for easy firmware upgrades

ISDN BRI Line

Before running the ISDN adapter, you need to get an ISDN BRI (Basic Rate Interface) line from your local telephone company. Your ISDN service provider will provide information to you about the ISDN central switch type, pertinent subscriber information and SPID (Service Profile ID) number(s) if required.

SPID (Service Profile ID)

The Service Profile ID (SPID) is applicable in the U.S. only. SPIDs are a series of numbers that inform the central office switch which services and features to provide to an ISDN device. The generic SPID format comprises 14 digits. The first 10 digits are the main telephone number on the terminal. The last 4 digits are dependent on the number of terminals on the interface and the services they support.

NT1 Connection

An ISDN Basic Rate (BRI) U-Loop consists of 2 conductors from the CO (telephone company central office) to the customer premises. The equipment on both sides of the U-loop has been designed to deal with the long length of the U-loop and the noisy environment it operates in. At the customer premises the U-loop is terminated by an NT1 (network termination 1) device. An NT1 is a device which provides an interface between the two-wire twisted-pairs used by telephone companies in their ISDN BRI network and an end- user's four wire terminal equipment. The NT1 drives an S/T-bus which is usually made up of 4 wires, but in some cases may be 6 or 8 wires.

The name of the S/T bus comes from the letters used in the ISDN specifications to refer to two reference points, Sand T. Point Trefers to the connection between the NT1 device and customer supplied equipment. Terminals can connect directly to NT1 at point T, or there may be a PBX (private branch exchange, i.e. a customer-owned telephone exchange). When a PBX is present, point S refers to the connection between the PBX and the terminal. Note that in ISDN terminology, "terminal" can mean any sort of end-user ISDN devices, such as data terminals, telephones, FAX machines, etc. The diagram which follows reflects interface points in a typical ISDN network.

5

Image 5
Contents Page Trademarks Model MTA128ST/NT S000305C Rev. CRevision Date Description Contents Product Description Introduction and DescriptionSpid Service Profile ID FeaturesIsdn BRI Line NT1 ConnectionPin Pin TE SignalInterlace LED Indicators LED P1 LED P2 LED LED Indicators Switch CompatibiltiyCommand Interface ConnectorsConnecting your TA Hardware InstallationSafety Warnings Connect the TA to Your PC RS-232 Connection Network Configuration Configuration UtilitiesIntroduction Before You StartVoice TEI Call Control ConfigurationDialing Numbers COM Port SettingsDCD Drop Time Configuring your TA Page Page Page Page Page Page Page Page AT Commands MTA128S T/NT Commands and S-RegistersAT Commands by Function Analog Pots Call Commands Digital Data Call Commands aRegisters Register SummaryAT Commands, S-Registers, and Result Codes Result Codes Using AT Commands to Operate the MTA128ST/NTAnswering a Call Making a CallAnswering Automatically Hanging UpAnswering Manually Specific Troubleshooting Situations Troubleshooting the TATroubleshoot ing IntroductionDebugging/Logging/Troubleshooting S-Registers Debugging/Logging/Troubleshooting CommandsNone of the LEDs light when the MTA128ST/NTis on Debugging/Logging/Troubleshooting Command Summary ATMTA128ST/NT does not respond to commands You can place data calls but not voice calls or vice versa MTA128ST/NT dials but cannot make a connectionYou cannot place two simultaneous data calls MTA128ST/NT cannot connect when answeringMTA128ST/NT disconnects while online File transfer appears slower than it should beApple Macintosh Compatibility Making PPP/MLPPP Connections Bonding Using the &, I and + CharactersSoftware Applications that can Format PPP Data Dynamic Bandwidth Allocation DBADBA Data Protocols DBA Features Bandwidth-on-Demand BOD-S60, S61, S62, and S63PPP/MLPPP Repair Procedures for U.S. and Canadian Customers Warranty, Service, and Tech SupportWarranty Repair Procedures for International Distributors Replacement PartsQuick Setup Example AppendixAConfiguration ProfilesQuick Setup Factory Profiles Loop Qualification Bearer ServiceAppendix B Ordering Your Isdn Li ne Using Isdn Ordering Codes IOCs M5 previously Generic Data M-1DN J3 previously Generic Data J-1DNCapability S previously Generic Data M Ordering Isdn Without IOCs Appendices Appendices FCC AppendixC FCCand Canadian RegulationCanadian Limitations Notice Firmware-based Configuration Utility AppendixD Configuration MethodsConfiguration via AT Commands Using AT Commands to Configure the MTA128ST/NTGlossary SymbolGlossary IETFInternet Engineering Task Force PPPMultilink Protocol or MP-is an Internet Glossary TA-Seeterminal adapter Information pages from a central resource. See also Isdn Canadian Regulation 56 Appendix IndexUart