Fostex X-34 Applying Effects, Refer to page 18 for more information on the mixdown steps

Page 25

Model X-34 Owner’s Manual

Applying Effects

You may apply effects to the X-34 signals during mixdown by connecting an external effects processor in line between the AUX SEND and AUX RTN connectors on the rear panel. The MON MIX/AUX knobs are used to adjust the amount of signal sent to the effects processor. The processed signals are returned to the X-34 via the AUX RTN connectors and mixed with the dry (no effect) sound. After adjusting the balance between the dry and wet sounds (using the AUX RTN knob), you can mix down to a connected master recorder.

You can also perform effect processing by connecting different effects, such as a compressor, limiter, noise gate, etc., to the LINE IN/INSERT jacks on the front panel during recording.

Choose the approach that suits your project.

Using the AUX SEND and AUX RTN connectors to apply effects at mixdown:

In this example, while mixing the sound sources recorded on tracks 1 ~ 4 and copying (dubbing) the mix to a master recorder, you apply effects to the desired track.

In this example, reverb is applied to tracks 2 and 4.

Be aware that if you want to add effects to individual tracks, you must add them during the mixdown process. You will be able to add an effect to the entire recording later if you wish. However, you will not be able to add an effect to a specific track; individual tracks will be inaccessible.

Master Recorder

Effects Processor

LINE OUT R

L

AUX RTN R

L

AUX SEND

PUNCH

DC IN

ON STANDBY

DOLBY NR

 

 

TAPE OUT

 

ON OFF

 

 

 

IN/OUT

12V

 

 

4

3

2

1

1.Connect the input of an external effects processor to the AUX SEND connector on the rear panel of the X-34.

2.Connect the outputs of the external effects processor to the AUX RTN connectors (L/ MONO, R) on the rear panel of the X-34.

3.Set up the master recorder and the X-34 for mixdown rehearsal as described in steps 1- 7 of the “Mixdown” section on page 18.

4.Play the tape and turn the MON MIX/AUX knobs on channel 2 and 4 clockwise to adjust the level of signals sent to the effects processor.

5.Set the parameters of the external effects processor, if necessary.

6.Use the AUX RTN knob to adjust the level of the effect signals.

7.Adjust the monitoring level using the MONITOR knob.

8.Adjust the entire output level using the MASTER fader.

Refer to page 18 for more information on the mixdown steps.

9.If the level settings are satisfactory, rewind the tape.

10.Start recording on the master recorder, and start playing the tape on the X-34 to mixdown.

25

Image 25
Contents Model Safety Instructions Precautions please read before use Table of ContentsUsing write-protection tabs Before UsingRehearsal Mode This fader controls the output level from Line OUT L and R Names and FunctionsPress this button to start playback This indicator lights up when you turn on the powerPress this button to fast forward the tape at high speed Press this button to rewind the tape at hight speedFront panel Plug in monitor headphones hereCompressor/limiter or other effect Plug in a microphone here Rear PanelPlug in the exclusive AC adapter packaged with X- 34 here Initial setup Initial mode after the X-34 is powered onBasic Operation Let’s Record Front panel Line IN/INSERT jack Remember the following before you start to recordRear panel MIC in 1/3, 2/4 jack Using both MIC in jack and Line IN/INSERT jack 12 5 Recording will be canceled the REC indicator turns off REC indicator lights up in redWhen you finish recording, press the Stop button Try recording on tracks 2-4 in the same wayBasic Recording 2 Recording with the rear panel MIC in jack MON MIX indicator rights up Basic Playback ProcedureUse the Monitor knob to adjust the overall monitor volume Overdubbing Multitrack RecordingTrack 2 level indicator lights up Track 2 enters REC Ready modeTrack Down indicator lights up Mixdown Track Down modePunch In/Out Recording Advanced OperationPunching in and out is illustrated below 10,14,15 Step on the foot switch again when you wish to punch outStep on the foot switch at the punch in point Ping-pong Recording Using the Auto Bounce FunctionTrack 4 is now specified as the ping pong destination REC indicator lights upBeware of oscillation during ping-pong recording Monitoring Tape SyncTape Sync connection example Recording a sync signalApplying Effects If the level settings are satisfactory, rewind the tapeRefer to page 18 for more information on the mixdown steps Follow the instructions on page 16 for overdubbing Adjust the effect signal on the compressor/ limiterProblem Points to check Action TroubleshootingBlock Diagram MaintenanceCleaning the head, roller and capstan Record/playback head Capstan and pinch rollerMIC Input x SpecificationsAffect of Immunity on This Equipment Declaration of EC Directive