Fostex X-34 owner manual Specifications, MIC Input x

Page 29

Specifications

MIC INPUT (x 2)

 

Connector

: X L R t y p e c o n n e c t o r

 

(Balanced)

 

: ø 6 PHONE jack (Unbalanced)

Input impedance

: 10kΩ or higher

Reference input level

: –50 ~ –10dBV

LINE/INSERT (x 4)

 

When using the LINE IN jack:

Connector

: ø 6 PHONE jack

Input impedance

: 10kΩ or higher

Reference input level

: –10dBV

When using the INSERT jack:

Connector

: ø 6 STEREO PHONE jack

 

(Tip :Return, Ring :Send)

AUX RTN (L/MONO, R)

 

Connector

: ø 6 PHONE jack

Input impedance

: 7kΩ or higher

Reference input level

: –20dBV

LINE OUT (L, R)

 

Connector

: RCA pin jack

Output load impedance

: 10kΩ or higher

Reference output level

: –10dBV

TAPE OUT (x 4)

 

Connector

: RCA pin jack

Output load impedance

: 10kΩ or higher

Reference output level

: –10dBV

PHONES

 

Connector

: ø 6 STEREO PHONE jack

Output load impedance

: 16 Ω or higher

Maximum output

: 20mW (at 32 Ω)

AUX SEND

 

Connector

: ø 6 PHONE jack

Output load impedance

: 10kΩ or higher

Reference output level

: –10dBV

MONITOR OUT (L/R)

 

Connector

: ø 6 PHONE jack

Output load impedance

: 10kΩ or higher

Reference output level

: –10dBV

Model X-34 Owner’s Manual

Recording Tape

: C - 90 (TYPE - 2 or HIGH

 

position) or shorter

Record tracks

: 4 tracks, one direction

Tape speed

: 9.5 cm/s, 4.75cm/s

Pitch control

: –50% – +12%

Noise Reduction

: Dolby B noise reduction

 

system

EQ

: 2-band, shelving

 

+/–12(HI : 10kHz, LO : 100Hz)

Tape rewinding time

: 150 seconds (when a C-60

 

tape is used)

Frequency response

: Mixer section; 20Hz ~ 20kHz

 

: Recorder section; 40Hz ~

 

14kHz

Heads

: 4-tracks, 4-channel recording/

 

playback 4-tracks, 4-channel

 

erase

Power supply

: Fostex AC adapter, AD-12C

 

DC 12V (12 ~ 16V), 11W

Weight

: Approx. 1.7 kg (excluding the

 

AC adapter)

Dimensions

: 335 (W) x 75 (H) x 247(D) mm

*Specifications and appearance are subject to change without notice for purpose of product improvement.

*Dolby Noise Reduction is manufactured under license from Dolby Laboratories Licensing Corporation.

*Dolby and the double-D symbol are trademarks of Dolby Laboratories Licensing Corporation.

29

Image 29
Contents Model Safety Instructions Precautions please read before use Table of ContentsRehearsal Mode Before UsingUsing write-protection tabs This fader controls the output level from Line OUT L and R Names and FunctionsPress this button to start playback This indicator lights up when you turn on the powerPress this button to fast forward the tape at high speed Press this button to rewind the tape at hight speedCompressor/limiter or other effect Plug in monitor headphones hereFront panel Plug in the exclusive AC adapter packaged with X- 34 here Rear PanelPlug in a microphone here Basic Operation Let’s Record Initial mode after the X-34 is powered onInitial setup Rear panel MIC in 1/3, 2/4 jack Remember the following before you start to recordFront panel Line IN/INSERT jack Using both MIC in jack and Line IN/INSERT jack 12 5 Recording will be canceled the REC indicator turns off REC indicator lights up in redWhen you finish recording, press the Stop button Try recording on tracks 2-4 in the same wayBasic Recording 2 Recording with the rear panel MIC in jack Use the Monitor knob to adjust the overall monitor volume Basic Playback ProcedureMON MIX indicator rights up Overdubbing Multitrack RecordingTrack 2 level indicator lights up Track 2 enters REC Ready modeTrack Down indicator lights up Mixdown Track Down modePunching in and out is illustrated below Advanced OperationPunch In/Out Recording 10,14,15 Step on the foot switch again when you wish to punch outStep on the foot switch at the punch in point Ping-pong Recording Using the Auto Bounce FunctionBeware of oscillation during ping-pong recording REC indicator lights upTrack 4 is now specified as the ping pong destination Monitoring Tape SyncTape Sync connection example Recording a sync signalRefer to page 18 for more information on the mixdown steps If the level settings are satisfactory, rewind the tapeApplying Effects Follow the instructions on page 16 for overdubbing Adjust the effect signal on the compressor/ limiterProblem Points to check Action TroubleshootingBlock Diagram MaintenanceCleaning the head, roller and capstan Record/playback head Capstan and pinch rollerMIC Input x SpecificationsAffect of Immunity on This Equipment Declaration of EC Directive