Telular SX4e TDMA technical manual Phonecell SX4e User Setup, User Setup Commands, Auto Send Delay

Page 12

PHONECELL SX4e USER SETUP

The SX4e can be programmed with an ordinary telephone, which is sometimes referred to as a POTS (Plain Old Telephone Service) phone.

NOTE: The User Setup mode is not accessible while you’re in a call.

In the following sections, an <entered value> is comprised of the digits 0 through 9. The digits '*' and '#' are considered invalid when used inside an <entered value>, and will cause that com- mand/value to be rejected.

If there are no key entries within any 2-minute period, the FWT will revert to its normal mode. Going on-hook (hanging up the phone) will exit the setup mode.

Correct entry of the commands below will be confirmed by the return of the programming tone, which signifies that the unit is ready to accept the next entry. Incorrect entry will result in a short, three tone sequence of rising frequencies, followed by the return of the programming tone, which again signifies that the unit is ready to accept the corrected entry.

How to Enter the User Setup Mode

Use the following access code to enter the User Setup mode:

Press: # * 0 * 1 2 3 4 5 6 7 8 #

The access code is 8 digits. If the access code is not 8 digits or does not match the access code, the Programming mode cannot be entered. This code is pre-programmed during production and cannot be changed.

If you enter the access code correctly, the dial tone should change to a different, steady “Programming” tone and the bottom LED indicator on the front of the Phonecell will blink alternately RED and GREEN to indicate that you’re in the programming mode.

USER SETUP COMMANDS

In-Call DTMF Signaling Option

Use the following key sequence to set the In-Call DTMF Signaling option:

Press: # * 10 * <In-Call DTMF option> #

The < > brackets represents the 1-digit in-call DTMF signaling option.

Enter 0 for In-Band Signaling;

1 for Out-of-Band Signaling;

2 for both In-Band and Out-of-Band signaling; 3 for neither.

Enter a value between 0 and 3, otherwise the FWT will not update or store this value; the existing stored parameter will remain. The factory default setting is 1 (Out-of-Band signaling).

Auto SEND Delay

Use the following key sequence to set the Auto SEND Delay

Press: # * 11 # * <Auto SEND Delay> #

Enter a value between 2 and 20 seconds, otherwise the Phonecell will not update or store this value; the existing stored parameter will remain. The factory default setting is 3 seconds.

Pulse Dial Option

Use the following key sequence to set the Pulse Dial option:

Press: # * 12 * <Pulse Dial option> #

Enter: 0 to disable pulse dialing capability

1 to enable pulse dialing capability.

Enter either 0 or 1, otherwise the Phonecell will not update or store this value; the existing stored parameter will remain. The factory default setting is 1.

SX4e TDMA 800 SX4e Tri-Mode

12

Technical Manual

Image 12
Contents Digital TRI-MODETDMA/PCS/AMPS Contents Safe Operation InstructionsImportant Notices Table of Contents Installation Antenna Location and SetupOptional Wall-Mount Installation Connect Your SX4e to AC Power AC PowerPlug in Your Telephone Connect the SX4e to a telephoneHOW to SET UP Your Phone Number Band Order DigitsPhonecell SX4e Operation Supplementary Services Network Dependent FAX and Data Transmission Caller IDFax and Data Applications Facsimile MachinesRefresh FWT to Digital Mode Originating Fax and Data CallsSending Data Receiving Fax and Data CallsPhonecell SX4e User Setup User Setup CommandsHow to Enter the User Setup Mode Auto Send DelayAudio Output Level Control Caller ID Format SelectionPhonecell SX4e Technician Programming Commands Roam Option Band Order System SelectionPost Receiver Off-Hook Option System Operator CodeCall-Answered Supervision Pulse Option PressCasplsduration * casplslevel # Line-Reversal Outgoing OptionRestore Factory Defaults Request Ring Back requestPeriodic Self Test Option Disconnect Pulse OptionPrimary B-Side Non-Standard Control Channel Option Secondary A-Side Non-Standard Control Channel OptionSecondary Control Channel Option Secondary Paging Channel OptionPhonecell SX4e Troubleshooting General Information and Safety Aircraft ChildrenBlasting Areas Potentially Explosive AtmospheresImportant Notices Warranty What this Warranty Covers and for HOW LongGeneral Provisions 06/11/02 Part Number