Telular SX4e TDMA technical manual Phonecell SX4e Operation

Page 8

PHONECELL SX4e OPERATION

How to Use the LED Status Indicators

Plug in the power supply.

Wait for the unit to initialize.

The three LED indicators on the front of your Phonecell will turn ON. The Tables below describe the modes and operation of the three indicators - see Figures 9 and 10.

LED 1 – Power Status Indicator

LED Color

LED Activity

Description

 

GREEN

Continuous

FWT Power ON

 

ORANGE

Continuous

Low-Voltage Detection

 

NONE (Dark)

None

No FWT Power

 

LED 2 – Cellular Status Indicator

LED Color

LED Activity

Description

 

 

 

GREEN

Continuous

Good Cellular Signal

 

 

Strength

GREEN

Flashing

Poor Cellular Signal

 

 

Strength

RED

Continuous

No Cellular Service*

*Contact your service provider to verify that cellular service is activated.

LED 3 – FWT Status Indicator

LED 1

LED 2

 

LED 3

Figure 9 - LED status indicators.

LED Color

LED Activity

Description

 

 

GREEN

Continuous

Normal Operation

 

 

GREEN

Flashing

Normal Operation - Analog

 

 

 

 

 

 

Fax Call

 

GREEN/RED

Alternating

Programming Mode

 

 

 

RED

Continuous

FWT Failure**

 

 

RED

Flashing

Phone or Fax Interface Failure

 

 

 

 

 

 

 

Check Wiring to Telephone

**Contact your Authorized Telular Service Representative

How to Place a Call

1)Pick up your telephone handset (your phone is now “off-hook”).

2)Listen for dial tone (If service is not available, a No-Service tone is produced. Hang up the phone and try again. If the No-Service tone continues, contact your service provider to make sure cellu- lar service is activated.).

3)Dial the phone number.

How to Receive a Call

When your telephone rings, pick up the handset and begin talking.

How to End a Call

Hang-up the phone (place the handset back onto the telephone cradle).

The Hookflash Function

When you initiate the Hookflash function, it automatically lets you:

Speed up the connection after you dial a phone number.

Answer an incoming call that occurs when you’re dialing a phone number.

Use special (supplementary) cellular services which may be available in your cellular service area.

How to Use the Hookflash Function

Depending upon your phone, there are two ways to initiate the Hookflash function:

Press the dedicated “HOOKFLASH” or “FLASH” key on your telephone.

Press the hang-up or switch-hook mechanism on your phone once quickly (approximately 1/2-second).

SX4e TDMA 800 SX4e Tri-Mode

8

Technical Manual

Image 8
Contents Digital TRI-MODETDMA/PCS/AMPS Important Notices ContentsSafe Operation Instructions Table of Contents Optional Wall-Mount Installation InstallationAntenna Location and Setup Connect Your SX4e to AC Power AC PowerPlug in Your Telephone Connect the SX4e to a telephoneHOW to SET UP Your Phone Number Band Order DigitsPhonecell SX4e Operation Supplementary Services Network Dependent FAX and Data Transmission Caller IDFax and Data Applications Facsimile MachinesRefresh FWT to Digital Mode Originating Fax and Data CallsSending Data Receiving Fax and Data CallsPhonecell SX4e User Setup User Setup CommandsHow to Enter the User Setup Mode Auto Send DelayAudio Output Level Control Caller ID Format SelectionPhonecell SX4e Technician Programming Commands Roam Option Band Order System SelectionPost Receiver Off-Hook Option System Operator CodeCall-Answered Supervision Pulse Option PressCasplsduration * casplslevel # Line-Reversal Outgoing OptionRestore Factory Defaults Request Ring Back requestPeriodic Self Test Option Disconnect Pulse OptionPrimary B-Side Non-Standard Control Channel Option Secondary A-Side Non-Standard Control Channel OptionSecondary Control Channel Option Secondary Paging Channel OptionPhonecell SX4e Troubleshooting General Information and Safety Aircraft ChildrenBlasting Areas Potentially Explosive AtmospheresImportant Notices Warranty What this Warranty Covers and for HOW LongGeneral Provisions 06/11/02 Part Number